Vacon NX OPTCJ Скачать руководство пользователя

Страница: 24 / 26

24 • vacon

fault tracking

Tel. +358 (0)201 2121 • Fax +358 (0)201 212 205

FAULT TRACKING

The table below presents the faults related to the BACnet option board. For more information, see

also Vacon NX User's Manual, Chapter 9.

The BACnet option board status LEDs have been described in more detail in Chapter 5.

Fault

code

Fault

Possible cause

Correcting measures

Device change

Option board changed.

Reset

Device added

Option board added.

Reset

Device removed Option board removed.

Reset

Device
unknown

Unknown option board.

Fieldbus fault

-The board has lost all contact with other

devices on the network.
- Duplicate MAC ID (Bad Frames in
“Comm. status” is incremented every
time a frame is received from a device
with the same MAC id on the same
segment.)

Check the installation.

If installation is correct contact the
nearest Vacon distributor.
Check that MAC ID is unique.

Slot fault

Defective option board or slot.

Check the board and slot.
Contact the nearest Vacon distributor.

Table 8-1. RS-485 option board faults

You can define with parameters how the frequency converter shall react to certain faults:

Code

Parameter

Min

Max

Unit

Step

Default

Note

P2.7.22 Response to fieldbus

fault

733

0=No response
1=Warning
2=Fault,stop acc. to 2.4.7
3=Fault,stop by coasting

P2.7.23

Response to slot

fault

734

0=No response

1=Warning
2=Fault,stop acc. to 2.4.7
3=Fault,stop by coasting

Table 8-2. Frequency converter responses to faults

These BACnet Specific fault codes can be read from panel V7.x.2.3 (x is the used, D=4, E=5).

Fault

code

Fault

Possible cause

Correcting measures

None

Sole Master

Only device on the network

Add devices

Duplicate MAC ID

Some other device has the same MAC ID

Check MAC Addresses

Baudrate fault

Option card notices traffic, but can’t lock
to the selected baudrate.

Check Baudrate

Table 8-3. BACnet specific faults

Содержание NX OPTCJ



























Результаты поиска

Содержание NX OPTCJ

Отзывы:

Похожие инструкции для NX OPTCJ

Бренды по названию

Популярные бренды

Vacon NX OPTCJ, Руководство пользователя

Результаты поиска

Содержание NX OPTCJ

Отзывы:

Похожие инструкции для NX OPTCJ

Бренды по названию

Популярные бренды