VAC TZIDC, Инструкция по конфигурации и параметризации

Страница: 3 / 40

TZIDC, TZIDC-200 | COI/TZIDC/TZIDC-200-EN 3
Contents
1 Safety ............................................................................... 5
1.1 General information and instructions .................... 5
1.2 Warnings ............................................................. 5
1.3 Intended use ........................................................ 5
1.4 Improper use ....................................................... 5
1.5 Warranty provisions ............................................. 5
2 Operatio n ......................................................................... 6
2.1 Safety instru ctions ............................................... 6
2.2 Parameterization of the device ............................. 6
2.2.1 Menu navigation .................................................. 6
2.3 Menu levels .......................................................... 7
2.4 Operating modes ................................................. 7
2.4.1 Operating mode 1.0: Control with adaptation ....... 7
2.4.2 Operating mode 1.1: Control without adaptation .. 7
2.4.3 Operating mode 1.2: Manual adjustment in the
stroke ra nge ........................................................ 8
2.4.4 Operating mode 1.3: Manual adjustment in the
sensor range ........................................................ 8
2.5 Inhibiting operation .............................................. 8
3 Con fi gurat ion ................................................................... 9
3.1 General information .............................................. 9
3.2 Example .............................................................. 9
3.3 HART parameter description .............................. 10
3.4 HART parameter over view (graphic) ................... 12
3.5 Parametergroup 1: Standard ............................. 12
3.5.1 ACTUATOR – Actu ator type ............................... 12
3.5.2 AUTO_ADJ – automatic adjustment ................... 12
3.5.3 ADJ_MODE – Automatic adjustment mode ........ 13
3.5.4 TEST – Te st ....................................................... 14
3.5.5 FIND_DEV – Find device .................................... 14
3.5.6 EXIT – Return to op erating level ......................... 14
3.6 Parameter group 2: Setpoint .............................. 15
3.6.1 MIN_RGE – Setpoint range min. ........................ 15
3.6.2 MAX_RGE – Setpoint range max........................ 15
3.6.3 CHARACT – Character istic curve ....................... 15
3.6.4 ACTION – Direction of action (setpoint signal) ..... 15
3.6.5 SHUT_CLS – Shut-o ff value 0% ......................... 16
3.6.6 SHUT-OPN – Shut -o ff value 100%..................... 16
3.6.7 RAMP UP – Setpoint ramp (up) .......................... 16
3.6.8 RAMP DN – Setpoint ramp (down) ..................... 16
3.6.9 EXIT – Return to op erating level ......................... 17
3.7 Parameter group 3: Operating range .................. 17
3.7.1 MIN_RGE – Operatin g range min. ...................... 17
3.7.2 MAX_RGE – Operatin g range ma x. .................... 17
3.7.3 ZERO_POS – Zero position ................................ 18
3.7.4 EXIT – Return to op erating level ......................... 18
3.8 Parameter group 4: Messa ges ........................... 18
3.8.1 TIME_OUT – Dead band time limit ...................... 18
3.8.2 POS_SW1 – Switchin g point SW1 ..................... 18
3.8.3 POS_SW2 – Switchin g point SW2 ..................... 19
3.8.4 SW1_ACTV – Active direction SW1 .................... 19
3.8.5 SW2_ACTV – Active direction SW2 .................... 19
3.8.6 EXIT – Return to op erating level.......................... 19
3.9 Parameter group 5: Alarms ................................ 20
3.9.1 LEAKAGE – Leakage at actuator ........................ 20
3.9.2 SP_RGE – Setpoint monitoring .......................... 20
3.9.3 SENS_RGE – Operatin g range exceeded ........... 20
3.9.4 CTRLER – Contro ller inactive ............................. 20
3.9.5 TIME_OUT – Dead band time limit ...................... 20
3.9.6 STRK_CTR – Moveme nt counter ....................... 20
3.9.7 TRAVEL – Travel counter ................................... 21
3.9.8 EXIT – Return to op erating level.......................... 21
3.10 Parameter group 6: Ma nual adjustment ............. 21
3.10.1 MIN_VR – Operatin g range min. ......................... 21
3.10.2 MAX_VR – Operatin g range ma x. ....................... 22
3.10.3 ACTUATOR – Actu ator type ............................... 22
3.10.4 SPRNG_Y2 – Spring action (Y2) ......................... 22
3.10.5 DANG_DN – Dead Angle Close .......................... 23
3.10.6 DANG_UP – Dead Angle Open .......................... 23
3.10.7 BOLT_POS – Actua tor position .......................... 23
3.10.8 EXIT – Return to op erating level.......................... 23
3.11 Parameter group 7: Co ntrol parameters ............. 24
3.11.1 KP UP – KP va lue (up) ....................................... 24
3.11.2 KP DN – KP value (down) ................................... 24
3.11.3 TV UP – TV va lue (up) ........................................ 24
3.11.4 TV DN – TV va lue (down) ................................... 25
3.11.5 Y-OFS UP – Y o ff set (up) .................................... 25
3.11.6 Y-OFS DN – O ff s et (down) ................................. 25
3.11.7 TOL_BAND – Toler ance band ............................ 26
3.11.8 DEADBAND – Dead band .................................. 26
3.11.9 DB_APPR – Dead ba nd approach ..................... 26
3.11.10 DB_CALC – Dead-band determination ............... 26
3.11.11 LEAK_SEN – Leakage sensitivity ........................ 27
3.11.12 EXIT – Return to op erating level.......................... 27
3.12 Parameter group 8: Analog output ..................... 27
3.12.1 MIN_RGE – Current range min. .......................... 27
3.12.2 MAX_RGE – Current range max. ........................ 27
3.12.3 ACTION – Characteris tic curve action ................ 27
3.12.4 ALARM – Alarm ................................................. 28
3.12.5 RB_CHAR – Count back characteristic curve ..... 28
3.12.6 TEST – Te st ....................................................... 28
3.12.7 ALR_ENAB – Alarm vi a analog ou tput ................ 28
3.12.8 CLIPPING – Extending the signal output range ... 28
3.12.9 EXIT – Return to op erating level.......................... 28