background image

ENGLI

S

H

40

Start input function

This menu allows selecting input operation modes (see paragraph
“Activation inputs”):

StAn

Start and Pedestrian Start input standard operation, 
according to menu setups.

no

Start inputs from terminal board are disabled. Radio inputs 
operate in 

StAn

mode.

AP.CH

Start impulse always controls the opening phase, Pedestrian 
Start always controls  the closing phase.

PrES

Manned operation; the gate will open as long as the Start 
input stays closed and it will close as long as Pedestrian 
Start stays closed.

oroL

Timer-operation; the gate stays open while the Start input or 
Pedestrian Start input is closed; as soon as the contact 
opens, the pause count down will start.

Brake Function

This menu allows to activate the brake function, so that your gate stops
immediately because of command or safety intervention avoiding a
further movement. This inconvenience happens when a sliding motor
provided with single-plate clutch is installed on a very heavy gate: owing
to inertia, the gate does not stop immediately and it can move about
ten centimetres, reducing safety.

0

the brake function is never active

1÷10

the brake function is active. Le brake power is proportional to 
the set value

Following to an intervention of the safety edge or of the obstacle sensor
or of a STOP control, the braking has always the maximum power,
regardless of the set value (provided that higher than 0) to guarantee a
rapid reversion.

WARNING: each braking entails a mechanical stress to the 

components of the motor. We suggest to set the minimum value
with which there is a satisfactory stop distance.

Stop Input

This menu permits to select the functions associated to the 
command of STOP.

no

the input STOP is not available

ProS

the input STOP stops the gate: pressing the command 
START the gate continues the motion

invE

the command STOP stops the gate: at the next START the 
gate starts moving in the opposite direction.

NOTE: during the pause, the STOP command will stop the pause
time count, the next START command will always close the gate. 

Содержание Gold Series


























Отзывы: