manualshive.com logo in svg

Uson sprint iq, Руководство пользователя

Поделиться
Скачать
Uson sprint iq Скачать руководство пользователя страница 25

Menus

23

Chapter 3

Menus

3.0.1  Test Starting While in Menu System

While using the menu system, for safety reasons, the 

Start

 

Switch (or the ability to accept a start command) is not always 
enabled. While navigating in any part of the menu system which 
has the word “menu” in the title, the tester is prevented from 
starting a test.

An exception to this rule is allowed while viewing graphs. The 
tester will accept start commands so that the operator can view 
the test data on the graphs.

The 

Stop

 Switch is 

always 

enabled.

3.0.2  Navigation

There are two menu systems. One is accessed by pressing Enter at 
the Run screen to allow easy access to basic features. The other 
menu system is accessed in Program Mode and allows in-depth 
changes to system. 

This simple menu which is accessed from Run Mode is discussed 
beginning on the following page. 

Remember that Sprint iQ is available in many 
configurations. Therefore, each tester may not display 
every menu item shown in the following pages.

Содержание sprint iq



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды