background image

Order of Assembly  

 
  

 

Figure 1-12: 

 

This figure shows all the main components for assembling a 12x8 floor  
and It shows the proper sequence the floor panels are to be assembled. 
Always finish the first row of panels before starting the second. 
Finish the second row before starting the third and so on.                                  

       Main 

 

 

                

 

 

 

 

 

 

Power Cable 

NOTE:

 It is always a good idea to power up and test the floors

      

             after assembling  a row to confirm all connections. 

  
 

        

’ tri

 end  

 

                       

8’ e te sio  tri

 

 
 
 
 
 
  

 

 

 

   

  3 

 

 

 

  2 

 

            1 

                      Third Floor                                     Second Floor                        First Floor 
                           Panel                                                 Panel                                   Panel  
  
 
 
   

 

 

 

 

 

 

 

 

 

          
                     

8’ Tri  

 

 

 

 

 

 

 

 

 

 

 

 

        end 

 

 

  

 6 

 

 

 

  5 

 

 

   4 

                       Sixth Floor                                        Fifth Floor                        Fourth Floor     
                           Panel                                                 Panel                                   Panel  
 
 
 
 

NOTE:

  

All new floors come with brand new never been used plugs and sockets. This means they may 

tend to be stiff and fit tight at first. To fix this it is recommended to apply a little marine grease on all the 
connections.

 

 
 
 

The ARCH Portable Lighted Dance Floor System 

Copyright USA Dance Floor, LLC

 

Содержание ARCH-RGB

















Отзывы: