US Water Systems FNLT-100-HY Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 43

background image

8

Visit us online at www.USWaterSystems.com Give us a call at: 1-800-608-8792

Softener Preparation

Fusion NLT Tank Installation Instructions

WATER PRESSURE:

A minimum of 20 pounds of water pressure is required for regeneration valve

to operate effectively.

ELECTRICAL FACILITIES:

An uninterrupted alternating current (A/C) supply is required. Note: Other

voltages are available. Please make sure your voltage supply is compatible with your unit before installation.

EXISTING PLUMBING:

Condition of existing plumbing should be free from lime and iron buildup.

Piping that is built up heavily with lime and/or iron should be replaced.

LOCATION OF FUSION NLT TANK AND DRAIN:

The Infusion tank should be located close to a drain

to prevent air breaks and back flow.

CAUTION:

Water pressure is not to exceed 80 psi, water temperature is not to exceed 110°F (43°C),

and the unit cannot be subjected to freezing conditions.

Media Installation

1) Remove the tank from carton.
2) Verify the riser tube is centered in the bottom center of the tank. A flashlight may be

necessary.

«
...
6
7
8
9
10
...
»

Содержание FNLT-100-HY












































Отзывы:

Нет отзывов

Похожие инструкции для FNLT-100-HY

Бренд: A.O. Smith Страницы: 62

ElectriFLEX LD LE Series

Бренд: Bradford White Страницы: 40

Бренд: A.O. Smith Страницы: 4

Бренд: START International Страницы: 2

Бренд: Sanela Страницы: 6

Gas Domestic Indoor Water Heater

Бренд: Rheem Страницы: 40

Бренд: Quietside Страницы: 44

IGLWCRFTL353CRHWH

Бренд: Igloo Страницы: 34

UNI DISPENSER 05

Бренд: UNIPRODO Страницы: 9

Бренд: Giant Страницы: 44

Бренд: lancer Страницы: 30

Бренд: lancer Страницы: 22

Бренд: MERQUIP Страницы: 20

VITOTHERM EI5 Series

Бренд: Viessmann Страницы: 16

Бренд: Thermo Concepts Страницы: 14

Бренд: KYOWA Страницы: 3

Бренд: Shini Страницы: 65

Бренд: Atmor Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды