US Water Systems FNLT-100-HY Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 43

background image

14

Visit us online at www.USWaterSystems.com Give us a call at: 1-800-608-8792

Softener Preparation

17) Place the valve on the primary tank adaptor and tighten the collar hand tight. DO NOT

use tools. Tightening the collar hand tight is sufficient.

18) Connect the tanks together using the stainless steel tubes. If the threaded adaptors

were previously installed, remove the red clips and pull the adaptors out.

19) Lubricate the O-rings on all threaded adaptors.

20) Install a threaded adaptor in the primary tank adaptor. Install the red clip to secure it.

Use channel locks to tight the short stainless steel tube to the treaded adaptor.

«
...
12
13
14
15
16
...
»

Содержание FNLT-100-HY












































Отзывы:

Нет отзывов

Похожие инструкции для FNLT-100-HY

Бренд: A.O. Smith Страницы: 64

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 4

120 through 250 Series

Бренд: A.O. Smith Страницы: 74

Бренд: Hewi Страницы: 4

Бренд: Spheros Страницы: 55

Бренд: vitapur Страницы: 39

Бренд: Gerber Страницы: 2

Бренд: Galmet Страницы: 16

KoolScapes CRYSTAL FLO CF500

Бренд: Koolatron Страницы: 2

AO-WH-SOFT-450T

Бренд: A.O. Smith Страницы: 49

5900-BT Neutralizer

Бренд: Clean Water Systems Страницы: 29

Water Filter CB20-302E

Бренд: Everpure Страницы: 2

Бренд: Everpure Страницы: 2

Бренд: Everpure Страницы: 2

Бренд: AOX Страницы: 2

Бренд: TRANSVEND Страницы: 12

Бренд: Hydropath Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды