US Water Systems FNLT-100-HY Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 43

background image

2

Visit us online at www.USWaterSystems.com Give us a call at: 1-800-608-8792

Safety Guide

For your safety, the information in this manual must be followed to minimize the risk of elec-
tric shock, property damage or personal injury.

Be sure to check the entire softener for any shipping damage or parts loss. Also note dam-
age to the shipping cartons.   Contact  US Water Systems at 1-800-608-8792 to report any
shipping damage within 24 hours of delivery.  Claims made after 24 hours may not be hon-
ored.
Small  parts,  needed  to  install  the  softener,  are  in  a  parts  bag.  To  avoid  loss  of  the  small
parts, keep them in the parts bag until you are ready to use them.

Unpacking / Inspection

PAGE

Unpacking / Inspection

3

Safety Guide

3

Proper Installation

4

Specification

7

Before Starting Installation

7

Installation Instructions

18

System Start Up

27

Programming Instructions

28

About The System

29

Maintenance

31

Sanitizing Procedure

35

Main Repair Parts

36

Trouble Shooting

41

Programming Chart

42

Warranty

43

Table of Contents



Check and comply with your provincial /
state and local codes. You must follow
these guidelines.



Use care when handling the water soften-
ing system. Do not turn upside down, drop,
drag or set on sharp protrusions.



The water softening system works on 12
volt-60 Hz electrical power only. Be sure to
use only the included transformer.



Transformer must be plugged into an in-
door 120 volt, grounded outlet only.



Use clean water softening salts only, at
least 99.5% pure. Extra Course Grade or
Crystal salts are recommended. Do not

use rock, block, granulated or ice cream
making salts. They contain contaminants
that could cause maintenance problems.



Keep the salt lid in place on the softener
unless servicing the unit or refilling with
salt.



WARNING

: This system is not intend-

ed for treating water that is microbiologi-
cally unsafe or of unknown quality without
adequate disinfection before or after the
system. Contact US Water Systems for
disinfection treatment equipment.

«
1
2
3
4
...
»

Содержание FNLT-100-HY












































Отзывы:

Нет отзывов

Похожие инструкции для FNLT-100-HY

Бренд: tatsuno Страницы: 13

Бренд: 4rain Страницы: 44

Бренд: STRATOS Страницы: 12

Бренд: AMICUS Страницы: 12

Бренд: AquaticLife Страницы: 8

Water Purification System NF 1.5"

Бренд: Hellenbrand Страницы: 2

Бренд: EcoWater Страницы: 7

Бренд: clage Страницы: 28

Бренд: Franke Страницы: 12

Бренд: Follett Страницы: 24

Raytherm - Type WH 926-1758

Бренд: Raypak Страницы: 2

Бренд: John Wood Страницы: 39

Бренд: A.O. Smith Страницы: 36

Бренд: Sanela Страницы: 12

Бренд: Grindmaster Страницы: 2

Бренд: Grindmaster Страницы: 36

Бренд: Navien Страницы: 20

Бренд: Miomare Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды