Urrea DLL21 Скачать руководство пользователя страница 20

20

Install the body bracket (Fig.27-1) on the seat 
assembly. Align. Use the screw removed before 
to fix and not tighten.

Use the fix supporting bracket (Fig.28) to con-
nect the body bracket and the body and insert 
the screw to fix.
Connect the air source hose (Fig29-2) and use 
Y Tee to connect the outlet hose and the other 
end connect with the inlet of the assistant 
pressure adjusting valve.

Connect the air source, insert the press cone 
roller connect rod (Fig.30-1) into the rota-
tion shaft hole (Fig.30-2) of the rotation arm. 
Handle manual direction change valve to make 
the tip of the press cone roller coincide to the 
center of the turntable (Fig.31). If not coincide, 
use the screw to adjust the position of the base 
to realize the coincide. After adjustment, fix 
the bolt.  

According to the Fig.32, fix the fix bracket 
on the body and fixes the tool box on the fix 
bracket and then use the lock nut to tight. 

As Fig.33, fix the cone support on the body 
bracket and install the press cone on the 
bracket.

Loose the nut below the base and turn the 
screw clockwise until it against the ground and 
tight (Fig.34) and install the side panel and tool 
box removed.
At this moment, the installation of the left as-
sistant completed.

INSTALL THE RIGHT ASSISTANT

After detach the tire from the rim according 
to the instruction of the chapter IV, we can ex-
ecute the following operations. 
First, position the claw according to the dimen-
sion of the tire and then clamp the rim by the 
claw and position the tire press cone roller 
at the center of the rim(Fig.35). Push down 
the manual valve to press down the rim until 
the external rim of the rim is lower than the 
surface of the claw. At this moment, you can 
immediately lock the rim. Lift up the support 
arm and place it at the working position and 
take off the press cone roller and place it on 
the support. 
                          

Use the press (Fig.36-1) to press down the 
tire section by section rim detached from the 
mouth and use the brush to spread the lubri-
cant on edge of the lip. Position the demount 
tool (Fig.36-2) in the demount position. Place 
the press beside of the demount tool to press 
down the lip and insert the crowbar below 
the demount tool in between the rim and lip 
(Fig.37). 

Lift up the press and move it to the position 
opposite to the demount tool and press the lip 
into the tire detach groove and then rotate the 
crowbar to lift the lip onto the demount tool 
(Fig.38). Rotate the turntable to detach the up-
per lip. 

Fig.35

Fig.36

1

2

3

Fig.37

Fig.38

Fig.32

Fig.33

Fig.34

1

Fig.31

1

2

Fig.29

Fig.30

1

2

1

2

Fig.27

Fig.28

1

DLL21-DLL24 manual.indd   20

10/07/15   15:14

Содержание DLL21

























Отзывы: