30
DS4095-0003
GB
31
DS4095-0003
GB
5. CALLER’S ID FUNCTION
You may need to subscribe to a service offered by your telephone operator to use this function.
Furthermore, the caller’s ID function must be programmed on the PABX switchboard to enable the passage
of information between network and telephone. Follow the instructions in the switchboard manual.
The caller’s ID function is used to view the caller’s telephone number on the display.
5.1 WHEN YOU ARE AT HOME
The caller’s phone number will appear on the display after the fi rst ring.
Alternatively, the message
NOT AVAILABLE
(if the caller is in an area which is not covered by the
service).
The message REP, time and date of the last call will appear on the display if several calls were received by
the same number.
If the caller’s number is longer than 16 digits, the fi rst 16 digits will appear on the central line for approximately
two seconds. The remaining numbers (up to 20) will be alternated with the fi rst. The display will show also
the name alternated with the second part of the number if the number is stored in the phone book.
Simply pick up the handset or press
to answer the call.
5.2 BACK HOME
LED
will blink to indicate that you have received calls when you were away. The number of calls will
appear on the display.
Press
to display the numbers from the last call received. The icon
NEW
will appear next to the number to
indicate a new call. The icon
RPT
will appear to indicate that the number has called several times.
5.2.1 CALLING A RECEIVED NUMBER BACK
Display the number and press
CALL BACK
.
5.2.2 CUSTOMISING RECEIVED NUMBERS
A name (up to 16 characters) can be associated to a number and the received numbers can be stored in the
phone book.
Proceed as follows to program a number:
•
Press
or
to view the number in the phone book.
•
Press the
button. The message “
ENTER NAME
” will appear briefl y on the display.
•
Enter the name (maximum 16 characters) to be associated to the telephone number to be stored. Press
the button once or twice, as required (see table below). The cursor will move forward automatically after
approximately half a second. Press
DEL/SET
to delete the letter if you make a mistake.
•
Press the
button to confi rm. The message “
ENTER NUMBER
” will appear on the display.
•
Press the
button to confi rm and go to entering a new name (see § 4.5.1), otherwise press the
button twice to quit.
REP
New call
Call number
Month and day
Repeated call
Hours and minutes
The letters are cyclical. The fi rst will be repeated after the last.
6. LED PANEL
The LED panel is used to show the status of PABX local lines, extensions and day/night service. The LEDs
will come on to indicate when the local lines and extensions are busy. The day/night (GN) service LED will
came on when night mode is active. See your Urmet Domus switchboard instruction manual for additional
details on operation.
The LED panel may not work correctly when it is switched on for the fi rst time. Pick up and hang up the
handset several times to make the LED panel work correctly.
7. TROUBLESHOOTING
(
*
):
C
all technical service if the problem persists.
Check the telephone line and handset
connections (see §2.2 and §2.3).
Try to plug a telephone that you know is
in working order in to the socket if the
problem persists. The problem is due to
the telephone line if it persists.
FAULT
LIKELY CAUSE
SOLUTION (*)
With the telephone
connected to a PABX
switchboard, the REDIAL
function and the PRE-SET
numbers cannot be used.
No pauses in the dialled
telephone number.
Upgrade the Urmet Domus PABX
software or add a PAUSE between the
telephone line access code and the
number to be called
(see section 3).
The telephone is silent.
Faulty connections.
Button Pressed Pressed Pressed Pressed
once
twice
three times four times
1
Blank Blank Blank Blank
2
A
B
C
A
3
D
E
F
D
4
G
H
I G
5
J
K
L
J
6
M
N
O
M
7
P
Q
R S
8
T U
V
T
9
W
X Y
Z
*
Blank Blank Blank Blank
0
Blank Blank Blank Blank
#
Blank Blank Blank Blank
