urmet domus 1061/006A Скачать руководство пользователя страница 37

Страница: 37 / 68

DS1061-036A

5.4.4

Outputs Programming Menu

Only the two auxiliary relay outputs 1 and 2 are programmable. The output configuration determines which
alarms will cause the relay contact switching (excited relay).
Possible associations are:

•

Burglar

alarm

: the relay switches (for the alarm time) when the control panel receives an

Burglar

alarm or a Tamper alarm.

•

Pre-alarm

: the relay switches when the input 1 is activated. The relay stays excited until the Entry

time is elapsed.

•

Technological alarm

: the relay switches (for the alarm time) when the control panel receives a

Technological alarm.

•

Emergency

alarm

the relay switches (for the alarm time) when the control panel receives a

Emergency

alarm.

•

Low battery/failure alarm

: the relay switches when occurs one of the following failures:

Low battery.

Failure on PSTN telephone line or no GSM network

Burnt fuse

Bus line failure

Failure signallings stay active until failure is removed.

To an output can be associated only one of the above mentioned alarms.

Содержание 1061/006A





































































Результаты поиска

Содержание 1061/006A

Отзывы:

Похожие инструкции для 1061/006A

Бренды по названию

Популярные бренды

urmet domus 1061/006A, Инструкция по установке и программированию

Результаты поиска

Содержание 1061/006A

Отзывы:

Похожие инструкции для 1061/006A

Бренды по названию

Популярные бренды