manualshive.com logo in svg

UPLIFT 3-Leg Desk, Инструкция по эксплуатации

Поделиться
Скачать
UPLIFT 3-Leg Desk Скачать руководство пользователя страница 5

© UPLIFT Desk

 • 1-800-349-3839 • [email protected] • www.upliftdesk.com

5

F. 

Slide Crossbar rails (part 5) back into Crossbar 

ends (part 4). Ensure the slots of the Crossbar rails 
are facing inward. The slot on the Crossbar rail is 

offset; it will need to be aligned in a specific way to 

allow for the already installed Machine screws. Make 
sure that the Crossbar rail can slide all the way to 

the end of the Crossbar end. If it doesn’t fit, take the 
Crossbar rail out and flip it over, with the slots facing 

inward and near the top of the edge, further from 

the floor.

H. 

Attach each Foot (part 2) to the 2-leg 

assembly and the Small foot (part 3) to the 
one-leg assembly with the Zero Crossbar 
Bracket with qty 4 Machine Screws (part 13) 
each, and tighten bolts in a cross pattern.

I. 

Your UPLIFT Eco Corner desktop is pre-

drilled with threaded inserts.  Place the desk-

top on a clean surface on the floor, with the 

pre-drilled holes facing up, and carefully line 
up the holes in the frame with the holes on 
the desktop.Adjust the width of the two-leg 
assembly if needed. 

4

4

5

2

3

13

J. 

Insert and tighten eight (8) M6x10  

Machine screws (part 14) into the Crossbar  
ends (part 4), to secure the rails in place.  

K. 

Ensure that the base is lined up with the 

threaded inserts in underside of the desktop. 
Proceed with securing the desk base to the 
desktop using fourteen (14) of the 10-1/2’’ 
Machine Screws (part 15).

Install as follows:
 

3 per Side bracket 

6 total

 

1 per Crossbar end 

2 total

 

6 for the Zero Crossbar Bracket

14

15

Содержание 3-Leg Desk










Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды