© UPLIFT Desk
• 800-349-3839 • 512-614-3152 • [email protected] • upliftdesk.com
3
Package contents
Flat head screws
(M6x14; qty 8)
Pan head screws
(M6x14; qty 2)
VESA mount
VESA bracket
Slot cover
Keypad
Power cable
Connecting cable
Base
Lifting column
Housing
Keyboard tray
bracket
Keyboard tray
Worksurface
Worksurface
bracket
Pan head screws
(#10-24x5/8’’; qty 13)
Pan head screws
(M6x10; qty 4)
Pan head screws
(M4x12; qty 4)
VESA screws
(qty 1)
Cable clips
(qty 2)
Felt pads
(qty 4)
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA scr
ew
#10-24x1/2’
’
Pan Head
M5x10
Pan Head
M6x10
Fla
t Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA scr
ew
#10-24x1/2’
’
Pan Head
M5x10
Pan Head
M6x10
Fla
t Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
Step 2
(a)
Attach the Lifting column to the Base using four M6x14
Flat head screws. Make sure the vertical column is facing to-
wards the front.
(b)
Attach the Worksurface bracket to the front of the Lifting
column using four M6x10 Pan head screws.
Step 1
Position your base upside down, and place the Felt pads at
the four corners of the Base. Once in place, flip it over and
place the base on your desk, with the front lined up with the
front edge of your desk.
(a)
(b)
Keypad
Power cable
Connecting
cable
Step 3
Plug the Lifting column’s cable into the Connecting cable,
then plug the Connecting cable into the port marked “M1” in
the Control box. Plug the Keypad into the port marked “HS”
and finally plug the Power cable into the control box, and then
into a 120Vac wall outlet. Press the “up” arrow on the Keypad
to raise the Worksurface to a higher level for Steps 4 and 5.
IMPORTANT:
While raising the Worksurface keep the Keypad
steady by firmly holding it against the base or desktop.
Note:
If surface does not rise perform the reset instructions
in the TROUBLESHOOTING section on page 6-7.
Step 4
Unplug the Keypad only! Feed the end of the Keypad’s wire
through the top side of the Worksurface and fit the Keypad
into the pocket as shown. Press Keypad cable into the wire
channel on the underside of the Worksurface. Attach Work-
surface onto the Worksurface bracket using five #10-24x5/8’’
Pan head screws. Plug the Keypad back into the Control box.
Step 5
Attach the Keyboard tray bracket to the Worksurface using four
#10-24x5/8’’ Pan head screws. Then attach the Keyboard tray to
the Keyboard tray bracket also using four #10 24x5/8’’ Pan head
screws.
Caution:
Make sure that Keyboard tray of the assembled unit is
clear of the desk edge. When the unit is at it’s lowest position, the
Keyboard tray will be lower than the desk’s surface.
front
of base
