manualshive.com logo in svg

United CoolAir 4CA1901, Руководство по установке

Поделиться
Скачать
United CoolAir 4CA1901 Скачать руководство пользователя страница 34

34

FORM CIM 0203

TROUBLE SHOOTING

WARNING: Turn OFF power to unit before conducting any trouble shooting, unless the tests
you are performing require system operation. Keep hands, clothing and tools clear of electrical
terminals and rotating components.

NOTE: For operating and trouble shooting instructions for Marvel Controller or humidifier,
refer to specific operating instructions that accompany the unit.

ITEM

PROBLEM

PROBABLE CAUSE

SOLUTION

CODE

1

Control is erratic.

Wired improperly or

Check wiring connections

connections are broken

against schematic diagram.

Defective contactor

Repair or replace contactor.

2

Blower fails to start.

Overload tripped

Reset and check cause.

Marvel alarm

Clear alarm(s) after correcting problem.

Thermostat set too high

Adjust to desired temperature.

Complete loss of

Repair leak and recharge refrigerant system.

refrigerant charge

3

Compressor fails to

Head pressure too high

Check condenser for obstructions and remove.

start.

(high pressure switch

Check for the required water flow through the

open)

water regulating valve and the condenser coil.
Manually reset thermostat.
With Marvel, turn off alarm and reset.

PTCR will keep

Wait for PTCR to cool off. Compressor should

compressor OFF for

start in 3 - 5 minutes.

3 - 5 minutes

Drain pan switch open

Check if the unit is draining properly.

Low line voltage causing

Check power source for cause of

compressor to overheat

electric variation of line voltage.

Dry or icy evaporator coil Defrost and clean coil and replace dirty
(reduced air flow)

filters.

4

Compressor short
cycles.

Lack of refrigerant

Check for leak. Repair and recharge the

(bubbles in sight glass)

system.

Short cycling of

Make sure that duct connections are proper for

conditioned air

return air and supply air and ensure that they
do not mix with each other.

– continued on page 35

Содержание 4CA1901









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды