Unipulse F156 Скачать руководство пользователя страница 128

Страница: 128 / 160

8.EXTERNAL INPUT/OUTPUT (Amphenol Connector)

119

8-3. Input (Meanings of Signals)

・

Digital zero reset (Edge input)

Resets the zero point correction value by digital zero at the ON edge, and also cancels the zero

alarm if it has occurred.

・

Digital zero (Edge input)

Zeros the gross value at the edge input. However, the zeroing range is within the set digital zero

regulation value. If the value is outside this range, it is not zeroed but the weight error (zero

alarm) occurs.

・

Tare subtraction (Edge input)

Does tare subtraction at the edge input, and zeros the net value.

・

Tare reset (Edge input)

Cancels tare subtraction at the edge input.

・

Hold or judgment (Level input)

Valid only in simple comparison mode.

If either or both of setting code 27; over/under comparison mode, and setting code 28; U/L limit

comparison mode is set at 1 (comparisons are made when the external judgment input is ON),

level input of judgment will result, while in other cases, the weight value and the result of

comparison at the ON edge will be held until the input turns OFF. In the case of hold input,

operation will result on OR condition with the RY0014 signal.

・

Feed / Discharge (Level input)

Valid only in setting code 23; feed/discharge control mode is set at 2 (external selection

(external control input)).

Feed control will result at OFF, and discharge control will result at ON.

・

Sequence start (Edge input)

Valid only in sequence mode.

Starts the sequence at the ON edge. If the sequence stop is on the ON level, the sequence will

not start but sequence error 1 will occur.

Содержание F156

































































































































































Результаты поиска

Содержание F156

Отзывы:

Unipulse F156, Руководство по эксплуатации, Страница: 128 / 160

Результаты поиска

Содержание F156

Отзывы: