Uniden DXAI4588 Series страница 9 Скачать руководство пользователя

Страница: 9 / 68

Installing.the.Rechargeable.Battery.Packs.into.the.Handsets

Each handset is powered by a rechargeable battery pack. Once installed, the battery

charges automatically when the handset is placed in the base or charging cradle.

To install the rechargeable battery pack:

1) Press down on the handset battery case cover (use the finger indention for a better

grip) and slide the cover downward to remove.

2) Plug the battery pack connector (red & black wires) into the small jack inside the

battery compartment. (The connector notches fit into the grooves of the jack only

one-way.) Match the wire colors to the polarity label in the battery compartment,

connect the battery, and listen for a click to insure connection.

3) Make sure you have a good connection by slightly pulling on the battery wires. If

the connection is secure, the battery jack will remain in place.

4) Place the battery case cover back in the handset by sliding it upwards until it clicks

into place.

Note:.Use.only.the.Uniden.(BT-1006).rechargeable.battery.pack.supplied.

with.your.phone.

Содержание DXAI4588 Series





































































Результаты поиска

Содержание DXAI4588 Series

Отзывы:

Похожие инструкции для DXAI4588 Series

Бренды по названию

Популярные бренды

Uniden DXAI4588 Series, Руководство пользователя

Результаты поиска

Содержание DXAI4588 Series

Отзывы:

Похожие инструкции для DXAI4588 Series

Бренды по названию

Популярные бренды