Uniden DXAI4588 Series Скачать руководство пользователя

Страница: 55 / 68

Symptom

Suggestion

Messages are incomplete.

• The incoming messages may be too long. Remind callers to leave a brief

message.

• The memory may be full. Delete some or all of the saved messages.

After a power failure, the

outgoing message is deleted.

• Record your personal outgoing message again. The default message should

remain.

No sound on the base

speaker during call monitoring

or message playback.

• Adjust the speaker volume on the base unit.

Cannot access remote call-in

features from another touch-

tone phone.

• Make sure you’re using the correct PIN code.

• Make sure that the touch-tone phone you’re using can transmit the tone for at

least two seconds. If it cannot, you may have to use another phone to access

your messages.

Содержание DXAI4588 Series





































































Результаты поиска

Содержание DXAI4588 Series

Отзывы:

Похожие инструкции для DXAI4588 Series

Бренды по названию

Популярные бренды

Uniden DXAI4588 Series, Руководство пользователя

Результаты поиска

Содержание DXAI4588 Series

Отзывы:

Похожие инструкции для DXAI4588 Series

Бренды по названию

Популярные бренды