Unico MCV85 TOTAL CLEAN & TURBO, Инструкция по эксплуатации

Страница: 35 / 116

ENGLISH
| 35 |
Make sure that Chapters 1 and 2 have been performed and
proceed with the cleaning operations: steaming with suction
on at the same time to gently treat the surface.
It is possible to adjust the intensity of the steam by using the +/-
buttons (see Chapter 4); for this type of surface we recommend
the minimum level of steam.
It is possible to adjust the suction power by moving the cursor
on the handle.
The combined use of steam and suction allows the most
efficient sanitising of the surface, dissolving dirt, eliminating
grease, germs and mites, and above all makes it possible to
remove excess humidity left by the steam and reduce the
cleaning operations time.
9. CLEANING RUGS AND CARPETS
SUCTION ONLY FUNCTION
For suction alone, set the Multibrush to position A (no insert) by
pressing the pedal.
Make sure that Chapter 1 has been carried out and begin the
cleaning operations.
It is possible to adjust the suction power by moving the cursor
on the handle (4).
For suction only, in addition to the multibrush, it is possible to use
the floor Turbo brush. The Turbo brush thanks to a turbo system,
increased the effectiveness and efficiency of the suction
operations of textile surfaces, recommended for removing hair
and animal fur from rugs and carpet.
STEAM ONLY FUNCTION
For cleaning only with steam, set the Multibrush to position A
(no insert) by pressing the pedal. Make sure that Chapter 2 has
been carried out and begin the cleaning operations.
It is possible to adjust the intensity of the steam by using the +/-
buttons (see Chapter 4); for this type of surface we recommend
the medium level of steam.
STEAM - VACUUM COMBINED FUNCTION
to refresh and dry the surface
For steam cleaning and vacuuming, set the multibrush to
position A (no insert) by pressing the pedal.
Make sure that Chapters 1 and 2 have been carried out and begin
the cleaning operations.
It is possible to adjust the intensity of the steam by using the +/-
buttons (see Chapter 4); for this type of surface we recommend
the medium level of steam.
It is possible to adjust the suction power by moving the cursor
on the handle.
Combined use of steam and suction allows the most efficient
cleaning of the surface, dissolving dirt and removing grease,
germs and mites; it also brightens the colour of fibres and dries
surfaces more quickly.
PROGRAMMED MODE
only for UNICO MCV80
For this type of surface there is a pre-set cleaning program, see
Chapter 6.2.
10. CLEANING GLASS, WINDOWS AND TILES
STEAM ONLY FUNCTION
Ensure that the points in Chapters 1 and 2 have been performed.
10.1 Connect the 2-in-1 windows and upholstery brush to the
handle or the telescopic tube. Press the cursor and slide it forward
on the accessory in order to remove the rubber frame (20).
10.2 It is possible to adjust the intensity of the steam by using the
+/- buttons (see Chapter 4); for this type of surface we
recommend the medium level of steam.
10.3 Press and hold the steam trigger on the handle (15) and
steam the surface abundantly to dissolve the dirt.
10.4 Activate suction and run the brush over the surface to then
begin drying.
The 2-in-1 windows and upholstery brush allows cleaning to be
completed quickly and simply, without any marks or smears.
The combined use of steam and suction allows the most
efficient sanitising of the surface, dissolving dirt, and eliminating
grease and germs, and above all makes it possible to quickly
dry the surface reducing cleaning time.
WARNING: To clean glass surfaces in particularly cold seasons,
preheat the windows starting from a distance of about 50 cm
from the surface.
WARNING: For additional safety, test steam delivery on a
hidden part, leave the steamed part to dry to ensure that no
changes in colour or deformation have occurred.
To avoid any dirt in the dirt collector causing bad smells
(especially where liquids and/or steam humidity are
vacuumed), we recommend emptying and cleaning after every
use according to the methods described in Chapter 17.
For safety reasons, apply the steam lock on the handle during
vacuuming.
WARNING: Before cleaning leather or fabrics with steam,
consult the manufacturer’s instructions and always carry out a
test on a hidden part or on a sample of the material. Allow the
steamed part to dry to make sure that no changes in colour or
deformations have occurred.
To avoid any dirt in the dirt collector causing bad smells
(especially where liquids are vacuumed and/or steam is used),
we recommend emptying and cleaning after every use
according to the methods described in Chapter 17.
UNICO MCV80-MCV85 - M0S11431 - 1Q09:UNICO 30/08/2016 16.17 Pagina 35