Unico MCV85 TOTAL CLEAN & TURBO, Инструкция по эксплуатации

Страница: 38 / 116

ENGLISH
| 38 |
18.4 Lift the cap pulling upwards (34) and remove the mesh
filter (35).
14.5 Hold the handle of the multi-cyclonic unit and pull upwards
(36).
18.6 Wash the mesh filter (37) and the multi-cyclonic unit using
running water only (38).
18.7 Wring out the filter (37) and reassemble all the parts,
following the procedure in reverse order, ensuring that the mesh
part of the filter is facing upwards.
18.8 Remove the HEPA filter from the body of the appliance,
disconnecting it from the appropriate lever (39).
18.9 Rinse the HEPA filter using running water only and shake
gently to remove any excess dirt or water residue; before
replacing the filter in the appliance, leave to dry naturally away
from direct light and heat for at least 24 hours (40).
The filters should be fully cleaned approximately twice per year.
Should the appliance be used frequently for vacuuming liquid
dirt, repeat the operation more frequently.
19. CLEANING THE BOILER
(extraordinary maintenance)
Use Allen key no. 6.
To maintain maximum performance, clean the boiler once per
year and/or every 50 intense uses.
19.1 Fully empty the tank and remove the dirt collector.
19.2 Put the appliance on its side and remove the lid using a coin
(41).
19.3 Unscrew the boiler cap using Allen key no. 6 (42).
19.4 Pour 200 ml of tap water into the boiler.
19.5 Rinse the boiler and pour the water into the sink or into a
special container for dirty water. If the water is very dirty, repeat
the operation until the water is clean (43).
19.6 Insert 200 ml of water in the boiler and screw on the cap,
ensuring the seal is present and that it is correctly screwed on.
Replace the lid.
19.7 Fill the water tank again and close the door.
19.8 Turn the appliance back on.
Before using steam to clean, direct the jet into a sink or other
container until the steam is completely clean.
20. CLEANING THE MINI TURBO BRUSH
(extraordinary maintenance)
20.1 Rotate the locknut and remove the upper part of the mini
turbo brush.
20.2 Clean the inside of the brush and re-close following the
procedure in reverse order.
21. CLEANING THE FLOOR TURBO BRUSH
(extraordinary maintenance)
21.1 Remove the door and clean the inside of the brush.
21.2 Close the brush following the procedure in reverse order.
22. CLEANING THE VACUUM TUBES
(extraordinary maintenance)
22.1 Switch on the appliance by pressing the power switch.
22.2 Vacuum 0.5l of clean water from a container (44) and
empty the dirt collector.
22.3 Repeat the operation until the water in the dirt collector is
sufficiently clean.
22.4 With the dirt collector clean and dry, vacuum air for at least
5 minutes to completely dry the tubes.
22.5 Ensure that the dirt collector and filters are completely dry.
22.6 Make sure that the tubes are not clogged using the
cleaning brush:
1 - Cleaning the handle-side tube: insert the cleaning brush to
the end of the handle making sure that there are not blockages
and/or foreign bodies which could block suction.
2 - Cleaning the tube between collector and hose adapter: insert
the cleaning brush into the tube making sure that there are no
1
2 3
WARNING: Do not exceed the quantity of water indicated and
pour it slowly into the boiler, making sure not to let it overflow.
WARNING: Risk of scalding! When accessing the boiler
(removing the cap, filling up, emptying), ensure that the
appliance is switched off at the power switch and
disconnected from the mains for at least two hours.
WARNING: Steam.
Risk of scalding!
WARNING: Check the filters during cleaning. Replace the filters
when visibly damaged.
UNICO MCV80-MCV85 - M0S11431 - 1Q09:UNICO 30/08/2016 16.17 Pagina 38