UNI-T UDP3000S Series Скачать руководство пользователя страница 46

Страница: 46 / 49

Programming Manual UDP3000S Series

Instruments.uni-trend.com

:SYSTem:COMMunicate:LAN:APPLy

Format

：

:SYSTem:COMMunicate:LAN:APPLy

Function

：

Apply the network parameters that have been set.

Description

：

When use the command“:SYSTem:COMMunicate:LAN:xxxx”(xxxx represents other network setting

command in LAN) to set the network parameter, the setup parameter will not take effect immediately

and will not save to nonvolatile memory of the device. It must execute the command

“:SYSTem:COMMunicate:LAN:APPLy”to make the parameter validly and save permanently. You can

execute multiple commands to modify multiple parameters and then execute a single

":SYSTem:COMMunicate:LAN:APPLy" command together.

For Example

：

:SYSTem:COMMunicate:LAN:DHCP:STATe ON Turn on DHCPFunction.

:SYSTem:COMMunicate:LAN:APPLy

Apply the network parameters that have been

set.

:SYSTem:COMMunicate:LAN:DHCP[:STATe]

Format

：

:SYSTem:COMMunicate:LAN:DHCP[:STATe] {0|1|OFF|ON}

Function

：

Turn on/off DHCPFunction of the network.

Description

：

When use this command to set the network parameter, the setup parameter will not take effect

immediately and will not save to nonvolatile memory of the device. It must execute the command

“:SYSTem:COMMunicate:LAN:APPLy”to make the parameter validly and save permanently. You can

execute multiple commands to modify multiple parameters and then execute a single

":SYSTem:COMMunicate:LAN:APPLy" command together.

For Example

：

:SYSTem:COMMunicate:LAN:DHCP:STATe ON Turn on DHCPFunction.

:SYSTem:COMMunicate:LAN:APPLy

Apply the network parameters that have been set.

:SYSTem:COMMunicate:LAN:DHCP[:STATe]

？

Format

：

:SYSTem:COMMunicate:LAN:DHCP[:STATe]

？

Function

：

Query the switch status of DHCPFunction of the network.

Description

：

After the network parameter is set and before executing the

command“:SYSTem:COMMunicate:LAN:APPLy”, the result queried by this command is the temporary

parameter and it reflects the parameter data used when executing the command

“:SYSTem:COMMunicate:LAN:APPLy”. Otherwise, the result queried by this command is the currently

operating parameter of the device.

It returns“{ON|OFF}“.

For Example

：

:SYSTem:COMMunicate:LAN:DHCP:STATe?

Return

：

:SYSTem:COMMunicate:LAN:IPADdress

Format

：

:SYSTem:COMMunicate:LAN:IPADdress "x.x.x.x"

Function

：

Set IP address of the device.

Содержание UDP3000S Series


















































Результаты поиска

Содержание UDP3000S Series

Отзывы:

Похожие инструкции для UDP3000S Series

Бренды по названию

Популярные бренды

UNI-T UDP3000S Series, Руководство по программированию

Результаты поиска

Содержание UDP3000S Series

Отзывы:

Похожие инструкции для UDP3000S Series

Бренды по названию

Популярные бренды