background image

 

 

 

19-2021 Rev E, 06/05/07 

13 

 

WARNING 

UV Light Hazard 
Harmful to bare skin and eyes. 
Can cause temporary or permanent loss of vision. 

 
Never look at the lamps while illuminated.  Only view illumination by way of view port accessory.  
To prevent exposure to ultraviolet light, disconnect power to the V-Flex before servicing any part 
of the HVAC system. 
 

  

WARNING  

Prevent accidental exposure to service personnel. 
Install interlock switches on all access doors and affix UV warning labels to 
HVAC equipment. 

 

5.  Reconnect the power to the HVAC system. 
6.  Choose a location on the adjacent HVAC equipment for the HVAC maintenance label 

included in the V-Flex

 

Lamp Module packing box.  Choose a location that a future 

installer can easily see during all future HVAC maintenance or repair. 

7.  Adhere the HVAC maintenance label to the HVAC equipment access door or panel. 

 

  

CHECKOUT

 

 
The installer should verify that the ultraviolet lamps are operating only by viewing through view 
port accessory.  Do not attempt to look directly into the duct to see the illuminated ultraviolet 
lamp.  The installer should orient the owner to the unit by demonstrating use of the view port 
accessory and discussing how to determine when the unit is functioning properly without looking 
directly into the duct to see the illuminated ultraviolet lamp.  The installer should also emphasize 
the hot surface and electrical shock safety warnings.  The installer should leave the product data 
with the owner and review the lamp cleaning and lamp replacement procedures.  
 

OPERATION 
 
TROUBLESHOOTING AND SERVICE

 

 
The V-Flex has no field-serviceable parts.  Lamp cleaning is recommended as routine 
maintenance four times a year, or every three months (quarterly).  Annual lamp replacement  
is required.  See the Replacing the Lamp (Annually) section for detailed procedural  
information. 

 
MERCURY NOTICE

  

 
This device contains mercury in the sealed ultraviolet lamp.  Do not place your used lamp in the 
trash.  Dispose of properly. 
 

Broken Lamp Clean-up 
 
Do not use a household vacuum.  

Sweep debris into a plastic bag and dispose of properly.  

Contact your local waste management authority for instructions regarding recycling and the 
proper disposal of old lamp.  

 

Содержание High Output UV Device V-Flex

















Отзывы: