Ultrak CRX-501 Скачать руководство пользователя страница 56

Страница: 56 / 65

3-7

Normally closed contact

If an auxiliary contact is configured as normally closed; an ON command from

the transmitter opens the contact. The contact remains open until an OFF

command is sent to close the contact.

Normally open contact

If an auxiliary contact is configured as normally open; an ON command from

the transmitter closes the contact. The contact remains closed until an OFF

command is sent to open the contact.

•

Iris

Open/Close

If a motorized manual iris lens or a lens that has been modified for selectable

manual/automatic iris is installed, the iris open/close feature of the controller

can be used to control the iris of the lens.

Manual iris has to be selected on

the controller.

Refer to the controller user’s manual for selecting manual iris.

NOTE

Option C must be installed in the receiver for
selectable automatic/ manual iris.

Refer to the transmitter operator's manual for the procedures to perform the

functions of the control receiver. The following is a list of Diamond Electronics

standard transmitters and their manual number.

Содержание CRX-501


































































Результаты поиска

Содержание CRX-501

Отзывы:

Похожие инструкции для CRX-501

Бренды по названию

Популярные бренды

Ultrak CRX-501, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CRX-501

Отзывы:

Похожие инструкции для CRX-501

Бренды по названию

Популярные бренды