Ultra Start 22 SERIES Скачать руководство пользователя страница 15

Страница: 15 / 24

Menu 1 - Press

1 Flash 2 Flashes 3 Flashes

1 Ignition Lock Enabled Lock Only

Disabled

2 Siren Output Type 1 Type 2

All chirps

3 Lock&Unlock Options Double Unlock 3 second 3/4

second

4 Unlock/Disarm 125ms

750ms

5 Passive Locks Disable

Enable

6 Shock Sensor Disable

Enable

7 Passive Arming Type 1 Type 2

Disable

Menu 2 -Press

1 Flash 2 Flashes 3 Flashes

1 Secure Service Mode 15 seconds

5 seconds

2 Park Light Output 30 seconds (-) Park Light (+)

Park Light

3 Siren Timing 5ms 50ms

10ms

4 Button #4 ( Button) Trunk Release Garage Door

Car Finder

5 Siren/ Horn Output Horn

Siren

*Automatic Starters ONLY

5 Reservation Mode Manual

Auto

**Manual Starters ONLY

Menu 3 -Press

1 Flash 2 Flashes 3 Flashes

1 Lock/ Unlock Type Type 1 Type 2

Normal

2 Gas/ Diesel Negative 15 second

Gas/Positive

3 Rearm Output Type 1 Type 2

Rearm

4 Run Time 4 Min 45 Min

15 Min

5 Crank Time 10 seconds 3 seconds

5 seconds

6 Starter Disable/GWR Active Passive

GWR

7 Safety Start Mode Press twice

Press once

Menu 4 -Press

1 Flash 2 Flashes 3 Flashes

1 Low Idle Learn

Low Idle Learn

2 Adjust For Over Crank

Reduced by 10%

3 Adjust For under Crank

Increased by 10%

**Bold type indicates settings that are Factory Default.

System Reset

The system reset will clear any changes made to the Program Menu’s as well as the
Tach setting. When the system reset is complete the system must be Tach learned
before the remote starter will operate.

Turn the ignition key from “Off” to “On” 3 times,

ON-OFF-ON-OFF-ON

within

three seconds

(Leave the key in the

position)

Press and release the

Program Button

located on the antenna. The park

lights will turn on and the siren will chirp one time.

Then press and hold the

Program Button

until the park lights flash and the

siren will chirp 3 times slowly to confirm system reset.

System is now reset to factory defaults

NOTE:

System Reset

does not

delete the transmitter codes from memory.

* See the following pages for more detailed programming instructions.

REMOTE VEHICLE STARTER

INSTALL MANUAL

PAGE 15

Quick View Programming

Содержание 22 SERIES

























Результаты поиска

Содержание 22 SERIES

Отзывы:

Похожие инструкции для 22 SERIES

Бренды по названию

Популярные бренды

Ultra Start 22 SERIES, Инструкция по установке

Результаты поиска

Содержание 22 SERIES

Отзывы:

Похожие инструкции для 22 SERIES

Бренды по названию

Популярные бренды