Setting 2 Gas/Diesel Mode
(Auxiliary Connector Pin 12, 23xx series)
1) (-) Input 1 Flash/Honk (-) Glow Plug input. Waits maximum 30 seconds.
2) Time Delay 2 Flashes/Honks Waits for approximately 15 seconds.
*3) Gas/ (+) Input 3 Flashes/Honks Waits 2 seconds if no diesel input is detected.
Press & Release the Program Button 2 Times (Setting 2)
Confirmed with 2 LED flashes.
Press & Hold the Program Button
until the appropriate # of park lights/horn (optional) honks, then release.
Press & Release the Program Button
to proceed to the next step
.
Setting 3 Rearm Output (Auxiliary Connector Pin 1)
1) Type 1 1 Flash/Chirp Pulse after start and with lock.
2) Type 2 2 Flashes/Chirps Pulse after start only.
*3) Factory Re-arm 3 Flashes/Chirps Pulse with lock and after starter shutdown.
Press & Release the Program Button
3 Times (Setting 3) Confirmed with 3 LED flashes.
Press & Hold the Program Button
until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button
to proceed to the next step.
Setting 4 Run Time
1) 4 Minutes 1 Flash/Chirp Runs for approx. 4 minutes when activated.
2) 45 Minutes 2 Flashes/Chirps Runs for approx. 45 minutes when activated.
*3) 15 Minutes 3 Flashes/Chirps Runs for approx. 15 minutes when activated.
Press & Release the Program
Button 4 Times (Setting 4) Confirmed with 4 LED flashes.
Press & Hold the Program Button
until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button
to proceed to the next step.
Setting 5 Maximum Crank Time
1) 10 Seconds 1 Flash/Chirp 10 sec max time that the starter will stay engaged.
2) 3 Seconds 2 Flashes/Chirps 3 sec max time that the starter will stay engaged.
*3) 5 Seconds 3 Flashes/Chirps 5 sec max time that the starter will stay engaged.
Press & Release the Program Button
5 Times (Setting 5) Confirmed with 5 LED flashes.
Press & Hold the Program Button
until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button
to proceed to the next step.
Setting 6 Anti-Grind/Starter Kill
(Auxiliary Connector Pin 4)
1) Active 1 Flash/Chirp (-)When locked and during remote start (Anti-Grind).
2) Passive 2 Flashes/Chirps (-)When locked/ 30 seconds after ignition is OFF or
pressed
*3) GWR 3 Flashes/Chirps (-) Output during remote start only. (Anti-grind/ Bypass)
Press & Release the Program Button
6 Times (Setting 6) Confirmed with 6 LED flashes.
Press & Hold the Program Button
until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button
to proceed to the next step.
Setting 7 Safety Start
1) Safety On 1 Flash/Chirp Press the
button twice within 3seconds to remote start.
*2) Safety Off 2 Flashes/Chirps Press the
button once to remote start vehicle.
Press & Release the Program Button
7 Times (Setting 7) Confirmed with 4 LED flashes.
Press & Hold the Program Button
until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button
to proceed to the next step.
REMOTE VEHICLE STARTER
INSTALL MANUAL
PAGE 19
Menu 3- Starter Settings
- continued
