Ultra Start 22 SERIES Скачать руководство пользователя страница 17

Страница: 17 / 24

Setting 1 Secure Valet Mode

(time required to set the system into Service Mode)

1) Secure Valet 1 Flash/Chirp Hold the Program Button for 15 seconds

*2) Normal Valet 2 Flashes/Chirps Hold the Program Button for 5 seconds

Press & Release the Program Button 1 Time

(Setting 1) confirmed 1 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/siren chirps, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 2 Parking Light/Trunk Output

(14 pin auxiliary connector pins 2&8)

1) 30 sec. Output 1 Flash/Chirp On for 30 seconds when

is pressed

2) Negative Park Lights 2 Flashes/Chirps Switches the Park Lights/Trunk Outputs

*3) Park Lights 3 Flashes/Chirps 2 Flashes when

is pressed

Press & Release the Program Button 2 Times

(Setting 2) confirmed 2 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/siren chirps, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 3 Siren Chirp Timing

(14 pin auxiliary connector pin 5)

1) 5 ms Pulse Output 1 Flash/Chirp Short(Quiet) siren Output
2) 15 ms Pulse Output 2 Flashes/Chirps Long(Loud) siren Output

*3) 10 ms Pulse Output 3 Flashes/Chirps Normal(Medium) siren Output

Press & Release the Program Button 3 Times

(Setting 3) confirmed 3 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/siren chirps, then release.

Press & Release the Program Button

to proceed to the next step.

REMOTE VEHICLE STARTER

INSTALL MANUAL

PAGE 17

Menu 1- User Settings

...continued

Setting 6 Sensor Enable/Disable

1) Sensor Disabled 1 Flash/Chirp Impact Sensor Disabled

*2) Sensor Enabled 2 Flashes/Chirps Impact Sensor Enabled

Press & Release the Program Button 6 Times

(Setting 6) Confirmed with 6 LED flashes.

Press & Hold the Program Button

until the appropriate # of park lights/ siren chirps, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 7 Passive/Active Arming

1) Passive Arming 1 Flash/Chirp Auto Arms 30 seconds after last door is closed
2) Active Arming with Rearm 2 Flashes/Chirps If unlock is pressed and no door is opened

*3) Active Arming 3 Flashes/Chirps Arms with remote transmitter only

Press & Release the Program Button 7 Times

(Setting 7) Confirmed with 7 LED flashes.

Press & Hold the Program Button

until the appropriate # of park lights/ siren chirps, then release.

Press & Release the Program Button

to proceed to the next step.

Press and

Release the

button for

Menu 2

Ignition 3x

On/Off

On/Off On

Press and

Release the

Program

Button

Press and Release

the Program Button

# of Times for

Setting Chosen

Press and Hold

the Program Button

to Change Option

Menu 2- Additional Settings

Содержание 22 SERIES

























Результаты поиска

Содержание 22 SERIES

Отзывы:

Похожие инструкции для 22 SERIES

Бренды по названию

Популярные бренды

Ultra Start 22 SERIES, Инструкция по установке

Результаты поиска

Содержание 22 SERIES

Отзывы:

Похожие инструкции для 22 SERIES

Бренды по названию

Популярные бренды