Ultra-Aire 70H Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 28

background image

24

Ultra-Aire 70H Installation Instructions

www.Ultra-Aire.com | 1-800-533-7533

SERVICE

Symptom

Possible Reason

Troubleshooting Procedure

CAUTION!

TROUBLESHOOTING SHOULD BE PERFORMED BY A QUALIFIED HVAC TECHNICIAN.

Troubleshooting

Troubleshooting Procedure for Control
Related Issues
This method of diagnosis will test the 3 main
components of the control circuit individually to
indicate any potential problems. This is to be used
when the control will not activate the main unit.
1. Detach field control wiring connections from

the pigtails on the main unit.

2. Connect the yellow and green wire pigtails

together; only the fan should run. Disconnect
the wires.

3. Connect the yellow and blue wires pigtails

together; fan and compressor should run.
Disconnect the wires.

4. If this test works, the main unit is working

correctly from a control standpoint.

5. Reconnect field control wiring to the pigtails

on the main unit.

6. Remove the control panel cover and detach

the field wiring from the control connections.

7. Connect the yellow and green wires together;

only the fan should run. Disconnect the wires.

8. Connect the yellow and blue wires together;

fan and compressor should run. Disconnect
the wires.

9. If this test works, then the field control wiring

is ok.

10. If the problem persists, then the control is

most likely faulty.

WARNING!

ELECTRICAL SHOCK HAZARD:

ELECTRICAL POWER MUST BE PRESENT
TO PERFORM SOME TESTS. THESE TESTS
SHOULD BE PERFORMED BY A QUALIFIED
SERVICE PERSON.

Neither fan nor
compressor
running.
Dehumidification
is being called for.

Compressor is
not running.
Dehumidification
is being called for.
Fan is running.

1. Defective compressor

run capacitor.

2. Loose connection in

compressor circuit.

3. Defective compressor

overload.

4. Defective compressor.
5. Defrost thermostat open.

Compressor
cycles on and off.
Dehumidification is
being called for.

1. Low ambient

temperature and/or
humidity causing unit
to cycle through
defrost mode.

2. Defective compressor

overload.

3. Defective compressor.
4. Defrost thermostat

defective.

5. Dirty air filter(s) or air

flow restricted.

6. Defective fan or relay.

1. Dehumidifier unplugged

or no power to outlet.

2. Humidity control set

too high.

3. Loose connection in

internal or control wiring.

4. Defective compressor

relay.

5. Defective control

transformer.

«
...
22
23
24
25
26
...
»

Содержание 70H





























Отзывы:

Нет отзывов

Похожие инструкции для 70H

Бренд: NANO Страницы: 26

Бренд: Dantherm Страницы: 12

Бренд: Condair Страницы: 72

aroma humidifier

Бренд: Impulsion Страницы: 16

Бренд: Haier Страницы: 28

Бренд: Shini Страницы: 51

Бренд: Stadler Form Страницы: 26

Бренд: Hangzhou Conloon Electric Страницы: 9

Бренд: G21 Страницы: 84

Бренд: Qlima Страницы: 172

Бренд: Dantherm Страницы: 292

Бренд: Zibro Страницы: 44

Бренд: VEAB Heat Tech Страницы: 24

Бренд: Philips Страницы: 72

Бренд: Philips Страницы: 38

Бренд: Philips Страницы: 214

Бренд: Philips Страницы: 116

UE001-065 humisteam

Бренд: Carel Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды