Uhlenbrock digital Intelli Drive 2, Руководство пользователя

Страница: 14 / 18

CV Description Value range Value ex works
31 Pointer CV for CV banks 0,1,8 0
32 2nd pointer CV for CV banks 0, 1, 3, 4, 5, 255
255
33-46 Simple function mapping 0-255
Assignment of the function outputs to the CVs
CV 33 Light function button (F0) when driving forward 1
CV 34 Light function key (F0) when reversing 2
CV 35 Function key F1 4
CV 36 Function key F2 8
CV 37 Function key F3 16
CV 38 Function key F4 32
CV 39 Function key F5 64
CV 40 Function key F6 128
CV 41 Function key F7 0
CV 42 Function key F8
0
CV 43 Function key F9 0
CV 44 Function key F10 0
CV 45 Function key F11 0
CV 46 Function key F12 0
Assignment of the individual bits
Wert
Bit 0 Front light output 1
Bit 1 Rear light output 2
Bit 2 Function output A1 4
Bit 3 Function output A2 8
Bit 4 Function output A3 (SUSI/logic)
16
Bit 5 Function output A4 (SUSI/logic) 32
Bit 6 Rangiergang 64
Bit 7 Starting/braking deceleration 128
47 Motorola 1st trinary address (directly only with Motorola programming method) 0-255 12
48 Motorola 2nd trinary address (only with Motorola programming method) 0-255 0
49 Motorola 3rd trinary address (only with Motorola programming method) 0-255 0
50 Decoder Konfiguration 1 Wert 0-63 0
Bit 0=0 Do not use Motorola 2nd address 0*
Bit 0=1 Motorola 2nd address use 1
Bit 1=0 Do not use Motorola 3rd address 0*
Bit 1=1 Motorola 3rd address use 2
Bit 2=0 Do not replace light outputs 0*
Bit 2=1 Replace light outputs 4
Bit 3=0 Frequency light, A1 and A2 = 156Hz 0*
Bit 3=1 Frequency light, A1 and A2 = 24KHz 8
Bit 4=0 SUSI = SUSI 0*
Bit 4=1 SUSI = A3/A4 output function mapping table 16
51 Decoder Konfiguration 2 Wert 0-135 3, 131
Bit 0=0 Motor control from 0
Bit 0=1 Motor control a 1*
Bit 1=0 Motor control PID - Controller 0
Bit 1=1 Motor control SX - controller 2*
Bit 2=0 no dynamic period of motor control 0
Bit 2=1 Dynamic period of motor control 4
Bit 7=0 Light, A1/A2 PluX12 decoder (73145) 0
Bit 7=1 Light, A1/A2 cable/NEM decoder (not 73145) 128
53 Period of motor control in 100µs steps 0-255 40
54 Motor control P-constant of the PID controller 0-255 100
55 Motor control I-constant of the PID controller 0-255 40
56 Motor control D-constant of the PID controller 0-255 32
57 Regler Offset 0-255 6
58 Measuring gap for EMF measurement in 100µs steps 0-255 8
59 Factory reset (also possible via CV8) 0-4 0
1 = CV 0 - 256, and CV257 - 512 (RailCom® Bank 7)
2 = CV 257 - 512 (RailCom Plus
®
Banken 5 & 6)
3 = CV 257 - 512 (extended function mapping banks 1 & 2)
4 = CV 257 - 512 (PWM modulation function outputs banks 3 & 4)
60 Short-circuit monitoring Motor, function outputs, temperature control. - -
Switched on (do not change)
61 Constant for the temperature shutdown - -
62 Constant of short-circuit detection of the FKT outputs (do not change) - -
63 Constant of short-circuit detection of motor output (do not change) - -
64 Page Register 0-255 0
for CV programming with a Motorola control unit
65 Offset-Register 0-255 0
for CV programming with a Motorola control unit
66 Speed correction forward 0-255 0
67-94 Extended speed step characteristic curve for speed steps 1 - 28 0-255 each under.
95 Reverse speed correction 0-255
0