UFESA aspirador sin bolsa, Инструкция по эксплуатации

Страница: 13 / 37

3
Connect the other end of the hose (handle) with
the suction tube. In order to do it, press latch ”A” and
insert the tube into the hose’s handle so that latch “A”
is blocked in opening “B” .
4
Adjust the telescopic suction tube to the desired
length by sliding the slider according to the arrow and
pull the tube out/in.
5
Attach the selected nozzle or brush to the other end
of the suction tube.
6
Combination suction brush may be used to
vacuum hard flooring and carpets. In order to vacuum
hard surfaces - wooden, plastic floors, ceramic tiles,
etc. pull the brush out by pressing the switch on the
suction brush according to the drawing . When
vacuuming carpets, hide the brush (set the switch on
the suction brush to “ ”).
7
Grab the plug (3) and pull the cord out.
When pulling the power cord out, beware
of the yellow stripe signaling the end of
the cord. Persistent pulling (pulling on),
may damage the cord.
8
Insert the plug into the power outlet.
Before starting the vacuum, make sure that both
“CYCLONE” dust container has been fitted with the basic
EPA E11 filter and the outlet filter has been installed.
9 Switch the vacuum cleaner on by pressing ON/OFF
button.
10
Your vacuum cleaner comes with a power regulator
helping you to smoothly regulate its power. Power can
regulated with the slider.
11 Sliding the slider according to the marking (MAX
or MIN) will cause the suction power to increase or
decrease.
12
Your vacuum cleaner is also fitted with mechanical
suction regulator located on the hose handle. It allows
you to temporarily and slightly correct the suction
power without the need to use the slider.
Dismantling/attaching “CYCLONE”
dust container
Your vacuum cleaner comes with a removable
“CYCLONE” dust container (vacuum’s removable
module) that collects and holds the dirt. When
“CYCLONE” is full, you need to empty it.
C
Your vacuum cleaner is equipped with
safety valve located inside the vacuum’s
compartment. It opens automatically,
when the suction hose or any of the elements
attached to it get choked or “CYCLONE” dust
container is overfull. Once the valve opens, you
will hear a distinctive “whirring” sound coming
out of the machine.
1
Switch the vacuum off by pressing ON/OFF
button (5) .
2
Remove the plug from the power outlet.
3
Disconnect “CYCLONE” dust container from the
vacuum. To do this release “CYCLONE” dust container lever.
4 Move “CYCLONE” over the dust bin and press the
clip on the bottom lid and empty the container.
Now you should check EPA E11 basic
filter and if necessary, clean or replace it.
5
Close the bottom lid of the “CYCLONE” dust
container until you hear the click.
“CYCLONE” must be tightly closed.
Otherwise, the suction power may be
reduced.
6
Attach the emptied “CYCLONE” dust container to
the vacuum until you hear the click.
It is necessary to empty “CYCLONE” dust container when
you notice that:
a) your vacuum cleaner is vacuuming less effectively,
b) dust container is full.
Take apart filters and “CYCLONE”
assembly
Your vacuum cleaner comes with “CYCLONE” dust
container with cyclone filtration enabling you to vacuum
without the need to use traditional bag. Characteristically,
cyclone filter uses the phenomena of the spinning
stream of air in order to separate solid contaminants.
Contaminants are separated in the circular part of the
container, where the spinning air throws them at the
container’s wall; later they are moved to the container’s
next chamber. Pre-cleaned air is directed to EPA E11
filter that picks up and holds the finest dust fractions.
This washable EPA E11 filter has been fitted with
a special filtering material to enable rinsing the dirt
under running water and reusing the filter.
The vacuum’s outlet is fitted with “Microfilter” outlet filter.