UE 1XSWHH Скачать руководство пользователя страница 15

Страница: 15 / 23

IM_1XSW-02

www.ueonline.com

5000

10000

15000

20000

25000

30000

35000

40000

45000

110

130

150

170

190

210

230

250

hms

supply

Rload (max)
Rload (min)

NOTE:

Do not replace the One Series display module or pressure

sensor. Swapping these amongst devices will cause a mis-match

between the stored sensor calibration data and the pressure sensor.

For proper operation, the display module serial number must always

match the serial number inside the enclosure (See Figure 12).

These serial numbers must match for proper operation.

DISPLAY MODULE CALIBRATION

ACCEPTABLE SUPPLY VOLTAGES AND LOADS FOR 1XSWLL AND 1XSWHL

The graphs below provide a range of acceptable power supply voltages (in Volts) and series loads (in Ohms). This is useful when the One Series

is connected to non-standard PLC and DCS inputs or is connected in series with a relay or solenoid coil.

NOTE:

If you need assistance with determining the compatibility of the One Series with your PLC, DCS, or relay, we can help. Please have the manu-

facturer's model number ready when you call us. In rare cases, when the series resistor value is too large and falls out of the Acceptable Range,

placing another resistor across the input will allow it to work. Please call +1 (617) 923-6977 (Inside Sales) for assistance.

2000

4000

6000

8000

10000

12000

14000

16000

18000

Rload (Max)
Rload (Min)

supply

load

(Max)

Load

(Min)

1111

2593

4074

110

5556

150

7037

190

8519

230

10000

270

11481

310

12963

350

14444

390

15926

430

supply

load

(Min) = (V

supply

- 5)/0.1*A

*De-rate 0.001A per C above 25°C

load

(Max) = (V

supply

- 5)/0.0027A

1XSWLL Allowable Voltage / Load Characteristics

supply

load

(Max)

Load

(Min)

10000

600

13333

800

110

16667

1000

130

20000

1200

150

23333

1400

170

26667

1600

190

30000

1800

210

33333

2000

230

36667

2200

250

40000

2400

supply

load

(Min) = (V

supply

- 10) / 0.1A

De-rate 0.001A per °C above 25°C

load

(Max) = (V

supply

- 10) / 0.006A

1XSWHL Allowable Voltage / Load Characteristics

Figure 12

Graph 1

Graph 2

Содержание 1XSWHH
























Результаты поиска

Содержание 1XSWHH

Отзывы:

Похожие инструкции для 1XSWHH

Бренды по названию

Популярные бренды

UE 1XSWHH, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 1XSWHH

Отзывы:

Похожие инструкции для 1XSWHH

Бренды по названию

Популярные бренды