UE 1XSWHH Скачать руководство пользователя страница 8

Страница: 8 / 23

IM_1XSW-02

www.ueonline.com

Terminal Block and Torque Details for Flameproof, Non-Incendive and Intrinsic Safety Installations

Terminal

Description

Max. Wire Gauge

Min. Wire Gauge

Recommended Tightening Torque

TB1

3-Position

14 AWG

22 AWG

7 in-lbs.

TB2

4-Position

10 AWG

20 AWG

4.4 in-lbs.

TB3

2-Position

14 AWG

22 AWG

7 in-lbs.

INTRINSIC SAFETY WIRING DIAGRAMS - MODEL 1XSWLL

(Use Class 2 or SELV Power Supply Only)

Model 1XSWLL

is intended for direct connection to a PLC or DCS discrete input, or other suitable load (see graph 1, page 15). Power is

obtained and the discrete switch signal is provided by the same two-wire connection. Polarity must be observed. (refer to Table 2, page 6)

for switch ratings.

DO NOT CONNECT MODEL 1XSWLL DIRECTLY TO A POWER SUPPLY WITHOUT A SUITABLE LOAD IN SERIES WITH THE

SWITCH.

For 1XSWLL models, only one conduit opening is required. The unused conduit opening must include an explosion-proof/flameproof plug,

made from a corrosion-resistant material, suitable for all gas and dust groups as listed on the nameplate. Blanking elements from factory

have been tested with the enclosure as an assembly and carry no markings.

SELECTING AN INTRINSIC SAFETY BARRIER (Model 1XSWLL)

For Intrinsically-Safe (I.S.) installations, please reference the Control Drawing UE 62174–64 for Intrinsic Safety entity parameters and wiring

information (https://www.ueonline.com/support/product-drawings/). Model 1XSWLL must be wired to an approved I.S. galvanically isolated

barrier for Zone 0 EPL Ga and Class I, Division 1 classifications. The information provided is for reference only and is intended to act as a

guide in the selection of a suitable I.S. Barrier.

SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY.

Installation of Intrinsically-Safe circuits must be performed in accordance with the requirements of the government and/or other local

authority having jurisdiction. System components and installation methods must be approved by the appropriate recognized approval

authority.

There are two general types of I.S. Barriers, shunt diode (passive) safety barriers and transformer isolated barriers. Shunt diode safety

barriers are not recommended for use with model 1XSWLL.

Transformer Isolated Barriers:

Due to the unique method by which the model 1XSWLL operates, a specifically designed isolated barrier must be used. Any safety barrier

that adheres to NAMUR standard EN 60947-5-6 for proximity and dry contact switches may be used to achieve intrinsic safety with the One

Series model 1XSWLL.

Recommended NAMUR standard transformer isolated intrinsic safety barriers:

Fuchs models KCD2-SR-Ex1.LB and KFD2-SR2-Ex1.W.LB

Figure 4 (page 6) shows a typical wiring scheme depicting model 1XSWLL connected to a programmable logic controller (PLC), distributed

control system (DCS) or other logic solver discrete input.

Table 3

Содержание 1XSWHH
























Результаты поиска

Содержание 1XSWHH

Отзывы:

Похожие инструкции для 1XSWHH

Бренды по названию

Популярные бренды

UE 1XSWHH, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 1XSWHH

Отзывы:

Похожие инструкции для 1XSWHH

Бренды по названию

Популярные бренды