background image

37

H.

  Check pilot burner flame.

 See Figure 24.  Flame 

should be steady, medium hard blue enveloping 3/8 to 

½ inch of sensing probe.

I.

  Check main burner flame.

 See Figure 23.  Flame 

should have clearly defined inner cone with no yellow 

tipping. Orange-yellow streaks should not be confused 

with true yellow tipping.

Figure 23:  1 Inch Main Burner Flame

Figure 24:  Pilot Burner Flame

J

.  Check thermostat operation.

 Raise and lower 

temperature setting to start and stop boiler operation.

K.

  Check ignition control module shut-off.

 Disconnect 

pilot lead wires from gas valve.  If burners do not 

shutdown, determine cause of malfunction.  Replace 

necessary items and check operation.

L.

  Check low water cutoff 

(if so equipped).

1.  Adjust thermostat to highest setting.
2.  With boiler operating, open drain valve and slowly 

drain boiler.

VIII.  SYSTEM START-UP

 (continued)

3.  Main burners and pilot burner will extinguish and 

blower will stop when water level drops below low 

water cutoff probe. Verify limit, thermostat or other 

controls have not shut off boiler.

4.  Adjust thermostat to lowest setting. Refill boiler. 

M.

 Check limit.

 

Jumper Thermostat connections in boiler wiring 

harness.  Allow burners to operate until shutdown by 

limit.  REMOVE JUMPER.

N.

  Adjust gas input rate to boiler.

1.  Adjust thermostat to highest setting.
2.  Check manifold gas pressure. See Table 5 or rating 

label located in the boiler’s vestibule compartment.  

Adjust gas valve pressure regulator as necessary 

(turn adjustment screw counterclockwise to 

decrease manifold pressure, or clockwise to increase 

manifold pressure). If pressure cannot be attained, 

check gas valve inlet pressure. If less than minimum 

indicated in Table 5 or boiler’s rating label, contact 

gas supplier for assistance.

3.  Clock gas meter for at least 30 seconds. Use Table 

10 to determine gas flow rate in Cubic Feet per 

Hour.

Seconds 

for One 

Revolution

Size of Gas Meter Dial

One-Half 

Cu. Ft.

One

Cu. Ft.

Two

Cu. Ft.

30

60

120

240

32

56

113

225

34

53

106

212

36

50

100

200

38

47

95

189

40

45

90

180

42

43

86

172

44

41

82

164

46

39

78

157

48

37

75

150

50

36

72

144

52

35

69

138

54

33

67

133

56

32

64

129

58

31

62

124

60

30

60

120

Table 10:  Gas Flow Rate in Cubic Feet

 

  Per Hour

Содержание PVG3





































































Отзывы: