U.S. Boiler Company PVG3 Скачать руководство пользователя страница 13

Страница: 13 / 68

Install Vent Pipe, U.S. Boiler Gasketed Vent System.

1. Procedure for Joining U.S. Boiler Gasketed Vent

Pipe and Fittings. See Figure 3.
a. Wipe the male end of each joint using an alcohol

pad to remove any dirt and grease.

b. Align weld seams in pipes and use a slight

twisting motion to FULLY insert male end into

female end of joint. Ensure bead in male end

of pipe is below locking band and rest against

the end of the female pipe. Verify the factory-

installed gasket is not dislodged or cut.

c. Tighten locking band by HAND with a 5/16”

nut driver until snug plus ¼ turn. DO NOT

SECURE JOINTS WITH SHEET METAL

SCREWS OR POP RIVETS. DO NOT

PUNCTURE THE VENT SYSTEM!

d. Once the installation is complete, operate

appliance and inspect all joints to ensure that flue

gases and/or liquid condensate will not escape.

Separate Horizontal Venting System.

See Figures 4A,

4B and 5. See Figure 28 for Blower Vent Connector

Assembly.

Vent Piping

–

1. This boiler is supplied with components as standard

equipment for installation of the separate horizontal

venting system.

Figure 3: U.S. Boiler Gasketed Vent Joint Detail

III. VENTING (continued)

2. Do not exceed maximum vent lengths. Refer to

Table 4.

3. Recommended horizontal installation consists

of vent being sloped down ¼ inch per foot away

from boiler. See Figure 4A. See Figure 4B for an

alternate horizontal installation.

4. Use appropriate designed thimbles when passing

through combustible walls (thimble use optional for

noncombustible walls). Insert thimble through wall

from outside. Secure outside flange to wall with

nails or screws, and seal ID, OD and vent holes with

sealant material. Install inside flange to inside wall,

secure with nails or screws, and seal with sealant

material.

5. For noncombustible wall application when thimble

is not used, size opening such that bell with locking

band attached cannot pass through.

6. Join vent terminal to vent pipe. See Figure 5.
7. Insert vent pipe through thimble/opening from

outside and join to vent system. Apply sealant

between vent pipe and opening/thimble to provide

weathertight seal and prevent entry of combustion

products into building.

Содержание PVG3





































































Результаты поиска

Содержание PVG3

Отзывы:

Похожие инструкции для PVG3

Бренды по названию

Популярные бренды

U.S. Boiler Company PVG3, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PVG3

Отзывы:

Похожие инструкции для PVG3

Бренды по названию

Популярные бренды