U.S. Boiler Company ENHANCED 2 Series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 60

U.S. Boiler Company ENHANCED 2 Series Скачать руководство пользователя страница 56

56

APPENDIX I – IQ Control System (continued)

Part Number

Item Description

105648-01

Outside Reset

IQ Option Card, Domestic Hot Water Priority, for use with Option Control Panel, with Outside

Air Temperature Sensor with 60 inch lead, Instructions, Unit Pack. No additional pipe fittings required.

Contact Factory

Outdoor Reset

IQ Option Card, Domestic Hot Water Priority, for use with IQ Option Panel, less Sensor.

102946-01

Outdoor Air Temperature Sensor, 10k ohm, 60 inch lead.

102711-01

LWCO

IQ Option Card kit, Hot Water LF Module, Automatic Reset, for use with Option Control Panel, with

¾ inch NPT Probe, Instructions, Unit Pack. Additional pipe fittings are required.

102714-01

LWCO

IQ Option Card kit, Hot Water LF Module, Manual Reset, for use with Option Control Panel, with ¾ inch

NPT Probe, Instructions, Unit Pack. Additional pipe fittings are required.

102301-01

LWCO

IQ Option Card, Hot Water LF Module, Automatic Reset, for use with IQ Option Panel, less Probe.

102302-01

LWCO

IQ Option Card, Hot Water LF Module, Manual Reset, for use with IQ Option Panel, less Probe.

102305-01

LWCO

¾ inch NPT Probe.

102720-01

Aquastat

IQ Option Card, 130-220 Deg F, Manual Reset for use with Option Control Panel, Temperature

Sensor with 36 inch lead, Well, Sensor Clip, Instructions, Unit Pack. Additional pipe fittings are required.

102717-01

Aquastat

, IQ Option Card, 130-220 Deg F, 15 Deg F Adjustable Differential, Auto Reset, for use with Option

Control Panel, Temperature Sensor with 36 inch lead, Well, Sensor Clip, Instructions, Unit Pack. Additional

pipe fittings are required.

102292-01

Aquastat

IQ Option Card, 130-220 Deg F, Manual Reset for use with IQ Option Panel, less well, Less Sensor.

102293-01

Aquastat

, IQ Option Card, 130-220 Deg F, 15 Deg F Adjustable Differential, Auto Reset, for use with IQ Option

Panel, less Well, less Sensor.

102295-01

Limit Rated Temperature Sensor, 36 inch length.

102296-01

Limit Rated Temperature Sensor, 48 inch length.

104211-01

IQ LCD Display

, Boiler Exterior Mounted, STN Monochrome, White/Red backlight, 5Vdc Power Supply,

RS422 (RS485) Communication, Pure Black Bezel with Gateway, Wire Harness, Mounting Bracket, Logo Plate

and Instructions.

102725-01

IQ LCD Display

, Boiler Exterior Mounted, STN Monochrome, White/Red backlight, 5Vdc Power Supply,

RS422 (RS485) Communication, Pure Black Bezel.

102495-01

Enviracom/Modbus RS422 Gateway and 5 Vdc Power Supply for Communication Between the IQ Controls

and LCD Display, 24 Vac Power Supply Input.

Optional Components

Sy

stem Parts List

Additional Information List

Aquastat IQ Option Card Instruction Sheet - part number 103589-01
Outdoor Reset IQ Option Card Instruction Sheet - part number 105647-01
Low Water Cut-off IQ Option Card Instruction Sheet - part number 103591-01
LCD Display Kit - part number 105916-01

«
...
54
55
56
57
58
...
»

Содержание ENHANCED 2 Series





























































Отзывы:

Нет отзывов