U.S. Boiler Company ENHANCED 2 Series Скачать руководство пользователя страница 10

Страница: 10 / 60

3. PROVIDE COMBUSTION AIR

INSUFFICIENT COMBUSTION AIR

SUPPLY may result in the production and

release of deadly carbon monoxide (CO) into the home

which can cause severe personal injury or death.

Provide combustion and ventilation air in

accordance with the section "Air for Combustion

and Ventilation," of the

National Fuel Gas Code

ANSI Z223.1/NFPA 54, or clause 8.2, 8.3 or 8.4 of

4. CONNECT VENTING

IMPROPER VENTING may result in property

damage and the release of flue gases which

contain deadly carbon monoxide (CO) into the home,

which can cause severe personal injury, death or

substantial property damage.

INSPECT EXISTING CHIMNEY before

installing boiler. Failure to clean or replace

perforated pipe or tile lining will cause severe injury

or death.

Vent installation shall be in accordance with

"Venting of Equipment," of the

National Fuel Gas

Code

, ANSI Z223.1/NFPA 54, or "Venting Systems

and Air Supply for Appliances," of the

Natural Gas

and Propane Installation Code

, CAN/CSA B149.1,

or applicable provisions of the local building codes.
Observe all general venting guidelines provided in

Appendix B—Venting.

Additionally:

Install any of the following for this Category

I, draft hood equipped appliance:
a. Type B or Type L gas vent. Install

in accordance with listing and

manufacturer's instructions.

b. Masonry or metal chimney. Build

and install in accordance with local

building codes; or local authority having

jurisdiction; or

Standard for Chimneys,

Fireplaces, Vents, and Solid Fuel Burning
Appliances

, ANSI/NFPA 211 and/or

National Building Code of Canada

Masonry chimney must be lined with listed

chimney lining system. Clay flue lined

masonry chimneys do not meet venting

requirements for this appliance.

c. Do not use cellular core PVC (ASTM

F891), cellular core CPVC, or Radel

(polyphenolsulfone).

d. Do not cover non-metallic vent pipe and

fittings with thermal insulation.

Note: Non-metallic vent cannot be used

with this boiler.

Attach the vent damper with three

sheetmetal screws around the perimeter of

the flue collar (Figure 4-a). The vent damper

may also be mounted anywhere between the

flue outlet and the chimney within reach of

the electrical harness.
a. Do not modify either draft hood for vent

damper.

b. Maintain minimum 6" (152 mm)

between vent damper and combustible

construction.

c. Position indicator must be visible following

installation.

d. Provide access for service.

Vent connector shall be double-wall

insulated gas vent as supplied with this

boiler or Type B (double-wall) gas vent only.

Using sheetmetal screws, attach the vent

connector between the vent damper and the

vertical chimney (Figure 4-b).

Natural Gas and Propane Installation Code

, CAN/

CSA B149.1, or applicable provisions of the local

building codes.

Like all fuel-burning appliances, boilers need air to

operate reliably and safely.

Provide combustion air using the instructions in

Appendix A—Combustion Air.

Содержание ENHANCED 2 Series





























































Результаты поиска

Содержание ENHANCED 2 Series

Отзывы:

U.S. Boiler Company ENHANCED 2 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 10 / 60

Результаты поиска

Содержание ENHANCED 2 Series

Отзывы: