U.S. Boiler Company ENHANCED 2 Series Скачать руководство пользователя страница 41

Страница: 41 / 60

APPENDIX B1 – ATMOSPhERIC VENTING

GENERAL WARNINGS FOR ATMOSPhERIC VENTING SYSTEMS

USE ATMOSPHERIC VENTING only with

boilers approved for atmospheric venting as

noted in the

Specifications

Section of this

manual.

INSPECT EXISTING CHIMNEY

for obstructions

and deterioration and repair or line the chimney

prior to placing the boiler in service.

UNLINED MASONRY CONSTRUCTION is

prohibited for use as a chimney.

FIREPLACES AND FAN-ASSISTED GAS

APPLIANCES

must not be vented into the same

chimney space as this boiler. Vent connectors

serving appliances vented by natural draft shall not

be connected into any portion of mechanical draft

systems operating under positive pressure.

DO NOT REDUCE THE DIAMETER

of the vent

connector between the boiler and the chimney. It

must not be smaller than the outlet on the draft

hood, damper, or vent reducer supplied with the

boiler.

Exception:

National Fuel Gas Code

ANSI Z223.1/ NFPA 54, and

Natural Gas

and Propane Installation Code

, CAN/

CSA B149.1, allow vent downsizing when

vent size determined by their Vent Sizing

Tables is smaller than draft hood outlet/

vent damper. These codes require all of

the following:

(a) Total vent height (H) is at least 10 ft (3

m);

(b) Vent not reduced more than one table

size; and

is greater than 4 in. (102 mm) in

diameter (ES23 cannot use smaller

vent size).

UNLISTED VENT DAMPERS AND

OBSTRUCTIONS

in the vent pipe are prohibited.

THE VENT DAMPER supplied with the boiler

shall not be used to block the vent of any other

appliance.

Содержание ENHANCED 2 Series





























































Результаты поиска

Содержание ENHANCED 2 Series

Отзывы:

U.S. Boiler Company ENHANCED 2 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 41 / 60

Результаты поиска

Содержание ENHANCED 2 Series

Отзывы: