background image

QUICK START GUIDE

u-line.com

23

CONTROL FUNCTION GUIDE

FUNCTION

COMMAND

NOTES

ON/OFF

Press     and release

Unit will immediately turn On or OFF

Leave interior light on

Press      and release to leave interior 
light on for 12 hours; press again to 
deactivate

After 12 hours, factory default is restored; light will 
turn on when door is open

Adjust Temperature

Press      or       and release 

When the display is flashing, press      or      to 
adjust the set point temperature. Note: temperature 
displayed is the actual temperature inside unit

Toggle between ºF / ºC

Hold       and       for 5 seconds

The display will change units

Toggle between Freezer/
Refrigerator

Hold      for 5 seconds

Unit will “beep” and display will show the default set 
point for Refrigerator/Freezer

Enable Sabbath Mode

Press      and hold for 5 seconds and 
release

The oF / oC symbol will flash briefly after 5 seconds. 
Interior light and display will go dark and remain so 
until  user  resets  mode  -  unit  continues  to  operate                               

Disable Sabbath Mode

Press            and  release                                                                                                           Display and interior light return to normal operation

Showroom Mode

Hold      and      for 5 seconds

Display will show 

SH

 for 2 seconds. Interior light and 

display will function normally, but the compressor 
and fans will not energize.
Repeat command to return to normal operation. 
Display will show 

EH

 for 2 seconds.

This unit is Star-K certified. See www.star-k.org for more details.

DOOR ALERT NOTIFICATION

When the door is left open for more than 5 minutes:

•  A tone will sound for several seconds every minute

• 

 will appear in display

Close door to silence alert and reset

Control Operation

CONVERTIBLE FREEZER

Содержание Outdoor Onb115



































Отзывы: