manualshive.com logo in svg

TYCROP ProPass 180, Руководство оператора

Поделиться
Скачать
TYCROP ProPass 180 Скачать руководство пользователя страница 34

TYCROP Manufacturing Ltd.  

 

ProPass 180 Top Dresser Operator’s Manual  

‪

 

Check the Vortex Brush bristles for wear and damage.  

Safety Decals 

‪

 

Check that the safety decals are undamaged and 
legible. Otherwise, replace them. 

How to Maintain the Conveyor Belt 
System 

Conveyor Belt Tensioning Procedure 

Perform the tensioning procedure only if the belt is 
slipping, if it has been replaced, or if it has been loosened 
to replace other parts.

 

1.

 

Place the belt’s V-guide in the guides of the front and 
rear rollers.  

2.

 

Tighten the two belt adjustment nuts evenly until the 
belt is snug. (If necessary, remove the front idler roller 
cover and the rear chute cover.)  

3.

 

Fully load the ProPass with the heaviest material you 
expect to use. 

4.

 

With two wrenches, hold the end of the tensioner rod 
stationary, then loosen the locking nut, which is the 
nut closest to the end of the rod (Figure 23). 

Locking Nut 

 

Adjuster Nut 

 

Figure 23: Tensioner rod and locking nuts 

5.

 

Turn the conveyor belt on (with the on/off pendant) 
and check if the belt is slipping.  

6.

 

If so, stop the belt and tighten both adjuster nuts half a 
turn. Do not over-tension. 

7.

 

Repeat steps 5 and 6 until the conveyor belt stops 
slipping.  

8.

 

Tighten the locking nuts and install the yellow safety 
covers. 

Conveyor Belt Tracking Procedure 

The conveyor belt system is self-tracking. Both the front 
and rear rollers have a groove in the middle for the belt’s 
V-guide to run in. Sometimes, the belt may track outside 
the grooves. To track the belt: 

1.

 

Determine which side the belt is tracking towards.  

2.

 

Remove the yellow safety covers from both front 
corners. 

3.

 

On the side the belt is tracking towards, hold the end 
of the tensioner rod stationary, then loosen the locking 
nut and tighten the adjuster nut by two flats of the nut. 
See Figure 23. 

4.

 

Tighten both locking nuts and turn on the conveyor 
belt.  

5.

 

Check the tracking movement. Repeat the above steps 
until the belt tracks back to the correct position.  

I

MPORTANT

:

 

Be patient! Do not over-tension the belt. 

6.

 

Install both of the yellow safety covers. 

How to Lubricate the ProPass  

Lubrication Schedule 

•

 

Use an automotive, all-purpose grease. 

•

 

Lubricate regularly, after 25 hours of normal 
operation. 

•

 

Lubricate daily when operating in extremely dusty and 
dirty conditions. 

•

 

Lubricate all bearings, bushings, and chains. 

Page 30 

 

Maintenance Instructions 

Содержание ProPass 180













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды