TYAN Tomcat i7221 S5150 Скачать руководство пользователя страница 94

Страница: 94 / 110

Tomcat i7221 S5150

Chapter 4: SATA/RAID Setup (for SATA RAID model)

4-33

http://www.tyan.com

Warning

Take caution in using this option; Initialization will erase all Array
information from the selected drives. Any away using any of these drives as
members will be affected.

1. Select

Initialize Drives

Use the <

↑

> and <

↓

keys to highlight the disk you wish to Initialize and press

Insert

Repeat step 2 so that both drives to be initialized are selected.

4. Press

<Enter>

5. Read the warning message and ensure that you have selected the correct disk drives to

initialize. Type

to continue.

4.13.8 Disk Utilities

The Disk Utilities enable you to low-level format or verify the media of your Serial ATA hard
disks.

From the

Adaptec RAID Configuration Utility

menu, select

Disk Utilities

Adaptec RAID Configuration Utility

Arrow keys to move cursor, <Enter> to select option, <Esc> to exit (*=default)

Press the <Enter> key to select SATA Disk.

Adaptec SATA HostRAID Controller#0

Options

Array Configuration Utility

Disk Utilities

Содержание Tomcat i7221 S5150















































































































Результаты поиска

Содержание Tomcat i7221 S5150

Отзывы:

Похожие инструкции для Tomcat i7221 S5150

Бренды по названию

Популярные бренды

TYAN Tomcat i7221 S5150, Руководство пользователя

Результаты поиска

Содержание Tomcat i7221 S5150

Отзывы:

Похожие инструкции для Tomcat i7221 S5150

Бренды по названию

Популярные бренды