TYAN Tomcat i7221 S5150 Скачать руководство пользователя страница 69

Страница: 69 / 110

Tomcat i7221 S5150

Chapter 4: SATA/RAID Setup (for SATA RAID model)

4-8

http://www.tyan.com

8. Scroll to option 4 ‘Exit’ and press the <Enter> key to exit the RAID Configuration utility and

the following prompt will appear:

RAID Volumes:
ID Name Level Strip Size Status Bootable
0 RAID_Volume0 RAID0(Stripe) 128KB 68.9GB Normal Yes

Physical Disks:
Port Drive Model                   Serial #
0      WDC WD360CD-00FN   WD-WMAH91105870
3      WDC WD360CD-00FN   WD-WMAH91063877

Size Type/Status(Vol ID)
34.4GB
34.4GB

Member Disk (0)
Member Disk (0)

Intel (R) Application Accelerator RAID Option ROM v4.0.0.6211
Copyright (C) 2003-04 Intel Corporation. All Rights Reserved.

[ ]-Select [ESC]-Exit [ENTER]-Select Menu

DISK/VOLUME INFORMATION

[ ]

MAIN MENU

[ ]

1.   Create RAID Volume
2.   Delete RAID Volume
3.   Reset Disks to Non-RAID
4.   Exit

HELP

[ ]

Are you sure you want to exit? (Y/N):

CONFIRM EXIT

[ ]

9. Confirm the exit by pressing <Y> key.

Delete RAID Volume

Warning

By performing this operation, all data on the RAID drives will be lost.

1. Select option 2 ‘Delete RAID Volume’ from the main menu window and press the <Enter>

key to select a RAID volume for deletion. The following window will appear:

Warning

If your system currently boots to RAID and you delete the RAID volume
in the Intel RAID Option ROM, your system will become unbootable.

Deleting a volume will destroy the volume data on the drive(s) and
cause any member disks to become available as non-RAID disks.

Intel (R) Application Accelerator RAID Option ROM v4.0.0.6211
Copyright (C) 2003-04 Intel Corporation. All Rights Reserved.

[ ]Select [<ESC>]-Previous Menu [<DEL>]-Delete Volume

HELP

[ ]

DELETE VOLUME MENU

[ ]

Name Level Drives Capacity Status Bootable
RAID_Volume0 RAID0(Stripe) 2 68.9GB Normal Yes

EXISTING DATA WITHIN THIS VOLUME WILL BE LOST AND NON-RECOVERABLE.

WARNING:

Содержание Tomcat i7221 S5150















































































































Результаты поиска

Содержание Tomcat i7221 S5150

Отзывы:

Похожие инструкции для Tomcat i7221 S5150

Бренды по названию

Популярные бренды

TYAN Tomcat i7221 S5150, Руководство пользователя

Результаты поиска

Содержание Tomcat i7221 S5150

Отзывы:

Похожие инструкции для Tomcat i7221 S5150

Бренды по названию

Популярные бренды