TYAN S2505T Скачать руководство пользователя страница 24

Страница: 24 / 57

http://www.tyan.com

2.10 Connecting IDE and Floppy Drives

A variety of IDE and ATAPI-compliant devices can be installed on this motherboard, such as hard disk

drives (HDDs) and CD-ROMs.

Please keep in mind that on this motherboard, the pri-

mary IDE connector is

BLACK

, and the secondary IDE

connector is

WHITE

. See

the picture to the right

for an

example of the IDE cable properly connected to the

motherboard, with the

BLUE

end of the IDE cable

installed on the motherboard.

Pin 1 on the IDE cable is usually denoted by a red or col-

ored stripe down one side of the cable. That side of the

cable must match Pin 1 on the motherboard’s IDE con-

nector. There will also be a key pin on the cable that

matches with a notch in the IDE connector, to ensure

proper installation. Consult the documentation that came

with your IDE/ATAPI device, or contact the device’s

manufacturer for more details on installation.

Please note that UltraDMA-100/66 IDE HDDs require a

special 80-wire cable which has additional grounding

wires. This cable has been included with this mother-

board for your convenience. The UltraDMA-100/66

cable is backwards compatible with UltraDMA-33 and

legacy IDE HDDs.

BLUE end goes to IDE connector

NOTE:

Only Tyan-approved cables are recommended for this motherboard. If you are using
an existing configuration with older cables, your system might not function properly.
Use only Tyan-approved cables (i.e. the ones included with your motherboard).

Pin 1

Some symptoms of incorrectly installed HDDs are...

May be a Master/Slave configuration problem, bad
IDE cable, or BIOS mis-configuration. Consult the
HDD documentation or contact your HDD vendor.

May be a bad cable or lack of power going to the
drive. Check the cables for damage and bad con-
nections.

Usually means the cable was installed backwards.

Bad IDE cable or defective drives. Try another HDD,
or contact your HDD vendor.

Check power cables and cabling. May be a bad
power supply or IDE drive problem.

HDD lights are constantly on

HDDs are not auto-detected

No video or beeps during bootup

HDD does not power on

Hard Disk Drive Fail message at bootup

Содержание S2505T


























































Результаты поиска

Содержание S2505T

Отзывы:

Похожие инструкции для S2505T

Бренды по названию

Популярные бренды

TYAN S2505T, Руководство пользователя

Результаты поиска

Содержание S2505T

Отзывы:

Похожие инструкции для S2505T

Бренды по названию

Популярные бренды