Twisted Hobbys Big Turbo Beaver Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 41

background image

Rev: 2015.06.28.v01c

page 19

Install the cross members now in to the

slots of the part that was just

seperated. Note - this is a dry t... NO

glue at this time.

Find the motor mount in the wood kit

and remove it. Note - production kits

will have two different hole patterns to

accommodate different style motor

mounts.

In the fuselage half that is whole,

install the motor mount as shown using

the Wet Welders method... laser etched

rectangles facing rearward.

Carefully bring the two pieces together,

making sure that the slots in the foam

and the slots in the wood pieces are all

lining up. Don't forget to put glue in the

motor mount area.

Again... Using the Wet Welders method

apply Welders to all the FOAM areas

where the two up portions of the

fuselage joint together. Do not put any

glue on any of the wood pieces yet.

Make sure and get glue in all the

contact areas. Wipe away any excess

that squeezes out.

«
...
17
18
19
20
21
...
»

Содержание Big Turbo Beaver










































Отзывы:

Нет отзывов

Похожие инструкции для Big Turbo Beaver

Ultimate EP 3D Profile

Бренд: E-FLITE Страницы: 40

Бренд: LaTrax Страницы: 12

Бренд: Faller Страницы: 4

Grange Farm Tipper Wagon

Бренд: Bole Laser Craft Страницы: 6

Portable Pit Stop Ramp

Бренд: Race Ramps Страницы: 6

IMAGINEXT B9774

Бренд: Fisher-Price Страницы: 6

Бренд: marklin Страницы: 32

Бренд: Bengtson Company Страницы: 7

Super Heroes 6862

Бренд: LEGO Страницы: 64

F-4 Phantom-II FF-D007

Бренд: Fly Fly Hobby Страницы: 10

Laugh & Learn Puppy's Learning Car

Бренд: Fisher-Price Страницы: 4

Бренд: GREAT PLANES Страницы: 20

Бренд: Velleman Страницы: 9

Бренд: MRC Страницы: 2

Project Mc2 Ultimate Makeover Bag

Бренд: MGA Entertainment Страницы: 2

Techno Gears Aero Trax Plane 2.0

Бренд: The Learning Journey Страницы: 49

Бренд: Lionel Страницы: 12

Бренд: Faller Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды