Twisted Hobbys Big Turbo Beaver Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 41

Twisted Hobbys Big Turbo Beaver Скачать руководство пользователя страница 16

Rev: 2015.06.28.v01c

page 16

Position the holes in clevises as you did

with the LEF and secure them to the

rod with medium CA. Make sure that

the orientation is correct.

Connect the control rod to the servo

and aileron control horn as shown. If

any adjustments are needed they can

be done later with subtrim.

Repeat the process for the other side.

This completes the Wing building, it

can be set aside for now and work on

the fuselage can begin.

With the nozzle of the Welder’s tube,

squeeze a small bead of glue into the
respect slots and install the strips as

shown while the glue is wet. Note - One

of the long ones is left out for now.

Locate two of the 1x5x300 carbon strips

and one of the 1x5x200 carbon strip.

Make sure the slot in the foam is deep

enough to receive each of the strips.

Now that the Wing is complete the

fuselage is next. Using the tack up

method, attach the landing gear

fairings as shown with the slots lining

up between the two pieces

«
...
14
15
16
17
18
...
»

Содержание Big Turbo Beaver










































Отзывы:

Нет отзывов