TWERD Power Electronics MFC710 400V Series, Руководство пользователя

Страница: 84 / 98

Appendix C – Table of MFC710 frequency converter's parameters
Parameter / Name Function Available options / measurement unit Factory
setting
Change
during
operation
2.22 Motop. mode Motopotentiometer mode 0 – sending STOP signal (by pushing STOP button,
through RS or other possibilities) causes resetting of
motopotentiometer settings
1 – value of motopotentiometer setting is stored in
memory. There is no possibility of changing this
setting during stoppage.
2 – value of current referencing-unit setting traced by
motopotentiometer. Applied for gentle transmission
from current ref.-unit to motopotentiometer
3 – value of motopotentiometer setting stored in the
memory. There is a possibility of changing this
setting during stoppage.
Note:
0, 1, 2 : modes applied when current ref.-unit
(par. 2.2 or par. 2.3) is set on MotPot.
3: mode independent of current ref.-unit choice.
1 YES
2.23 Motop. time Time of increase/decrease
of motopotentiometer ref.-
unit 0.1 ... 320.0 s 10.0 s YES
2.30 fConst0 src Source of W1 signal for
referencing constant
speeds 000 Sw.Off – W1 = 0
001 In.C1 … 006 In.C6 – W1 = 1 when there is
voltage supplied on digital input DI1..DI6
007 Sw.On – W1 = 1
S ee section 4.2.4
005 In.C5 YES
2.31 fConst1 src Source of W2 signal for
referencing constant
speeds as above 006 In.C6 YES
2.32 fConst2 src Source of W3 signal for
referencing constant
speeds as above 000 Sw.Off YES
2.33 f Const 1 Constant frequency 1 -550.0 ... 550.0 Hz 10.0 Hz YES
2.34 f Const 2 Constant frequency 2 -550.0 ... 550.0 Hz 20.0 Hz YES
2.35 f Const 3 Constant frequency 3 -550.0 ... 550.0 Hz 25.0 Hz YES
2.36 f Const 4 Constant frequency 4 -550.0 ... 550.0 Hz 30.0 Hz YES
2.37 f Const 5 Constant frequency 5 -550.0 ... 550.0 Hz 40.0 Hz YES
2.38 f Const 6 Constant frequency 6 -550.0 ... 550.0 Hz 45.0 Hz YES
2.39 f Const 7 Constant frequency 7 -550.0 ... 550.0 Hz 50.0 Hz YES
2.40 Cfg. In.A0 Configuration of analog
input AI0
0-10 V
0 V = 0.0 %
10 V = 100.0%
10-0 V
0 V = 100.0 %
10 V = 0.0 %
2-10 V
2 V = 0.0 %
10 V = 100.0 %
10-2 V
2 V = 100.0 %
10 V = 0.0 %
AI0 operates only in voltage mode.
0-10 V YES
2.41 Cfg. In.A1 Configuration of analog
input AI1
Voltage mode Current mode
0-10 V
0 V = 0.0 % 0 mA = 0.0 %
10 V = 100.0% 20 mA = 100.0%
10-0 V
0 V = 100.0 % 0 mA = 100.0 %
10 V = 0.0 % 20 mA = 0.0 %
2-10 V
2 V = 0.0 % 4 mA = 0.0 %
10 V = 100.0 % 20 mA = 100.0 %
10-2 V
2 V = 100.0 % 4 mA = 100.0 %
10 V = 0.0 % 20 mA = 0.0 %
Note: switching between current/voltage mode is
done by a jumper – see section 2.2.
Example: “0-10” on the display indicates that the
analog output mode is 0-10V or 0-20mA - depending
on the jumper settings.
0-10 V TAK
2.42 Cfg. In.A2 Configuration of analog
input AI2 as above 0-10 V YES
2.43 In.A0 Scale Scale of analog
referencing-unit RefA0 -500.0 ... 500.0 % 100.0% YES
2.44 In.A1 Scale Scale of analog
referencing-unit RefA1 -500.0 ... 500.0 % 100.0% YES
84
Frequency converter MFC710 type. TWERD Power Electronics