background image

16

 

TP9KF-TUX   

Mar 2019-A 

 

SAFETY PROCEDURES 

 

·

 

Never allow unauthorized persons to operate lift. Thoroughly train new employees in the operation and care of 

the lift. 

·

 

Caution: the power unit operates at high pressure. 

·

 

Remove passengers before raising vehicle. 

·

 

Prohibit unauthorized persons from being in shop area while lift is in use. 

·

 

Total lift capacity is 9,000 lbs. with 2,250 lbs. per arm pad. Never exceed the capacity. 

·

 

When approaching the lift with a vehicle, center the vehicle between the columns so that the tires will clear the 

swing arms easily. Slowly drive the vehicle up between the posts. Have someone outside the vehicle guide the 

driver. 

·

 

Always lift vehicle using all four arms. Never use lift to raise one end or one side of vehicle. 

·

 

Prior to lifting vehicle, walk around the lift and check for any objects that might interfere with the operation of lift 

and safety latches

; tools, air hoses, shop equipment. 

·

 

Raise vehicles about 3

” and check stability by rocking. 

·

 

Prior to lowering vehicle, walk around the lift and check for any objects that might interfere with the operation of 

lift and safety latches

; tools, air hoses, shop equipment.   

·

 

After lowering, swing the arms out of the path and slowly drive the vehicle out. Have someone outside the 

vehicle guide the driver. 

 

ALWAYS LOCK THE LIFT BEFORE GOING UNDER THE VEHICLE. 

NEVER ALLOW ANYONE TO GO UNDER THE LIFT WHEN RAISING OR LOWERING. 

 

 

OWNER / EMPLOYER RESPONSIBILITIES

 

·

 

Shall establish procedures to periodically maintain, inspect and care for the lift in accordance with the 

manufacturer

’s recommended procedures to ensure its’ continued safe operations. 

·

 

Shall provide necessary lockout of energy sources per ANSIZ244.1 

–1982 before beginning any lift repairs. 

·

 

Shall not modify the lift in any manner without prior written consent of the manufacturer.

 

 

 

MAINTENANCE SCHEDULE 

The  following  periodic  maintenance  is  the  suggested  minimum  requirements  and  minimum intervals

; accumulated 

hours or monthly period, whichever comes sooner. If you hear a noise or see any indication of impending failure - 

cease operation immediately

 

– inspect, correct and / or replace parts as required. 

 

Содержание TP9KF-TUX


























Отзывы: