Tuthill KINNEY KT150 Скачать руководство пользователя страница 15

Страница: 15 / 50

Manual 1843 Rev B p/n 001843 0000

GENERAL

KT pumps should always be operated with the

pump in a vertical and level position. KT pumps

should never be installed in a horizontal or angled

position. Pump assembly should be placed on a

foundation and should be supported evenly. Pump

assembly should be leveled to within 0.02 in. (0.5

mm) in any 3.28 ft (1 m).

Any time the vacuum pump will be stored for an

extended period of time (longer than 6 months),

make sure it is protected from corrosion by

preparing it for long-term storage.

1. Fill the separator housing to halfway in the

sight glass with the Tuthill-recommended oil for

the pump.

2. Close off the pump suction and discharge

connections using blind flanges with gaskets.

The oil fill connection should be plugged tightly,

and the oil drain valve should also be plugged,

to avoid accidental loss of oil.

Drain the water jacket and any other heat

exchangers containing water.

4. Leave the water inlet and outlet connections

unplugged and remove the drain plug from the

bottom of the cooling jacket.

5. Reduce the tension on the drive belts by

lowering the motor mounting plate.

6. Rotate the shaft of both pump and motor

several revolutions by hand at least every 3 to

6 months to keep the lubrication and shaft load

distributed in the bearings and seals.

7. For pumps that have been in service, contact

the factory for complete instructions.

Safety

DANGER

Internal and external rotating

parts of the pump and driving

equipment can produce

serious physical injuries. The

pump should never be run

with the inlet or discharge

piping removed. If it becomes

necessary to inspect the

rotating parts of the pump or to

change the belt, be absolutely

sure that all power to the motor

controls has been shut off, the

motor controls are locked out,

and properly tagged before

proceeding.

WARNING

Vacuum pump housing

and associated piping or

accessories may become hot

enough to cause major skin

burns on contact as a result of

process conditions.

INSTALLATION

Содержание KINNEY KT150



















































Результаты поиска

Содержание KINNEY KT150

Отзывы:

Похожие инструкции для KINNEY KT150

Бренды по названию

Популярные бренды

Tuthill KINNEY KT150, Руководство оператора

Результаты поиска

Содержание KINNEY KT150

Отзывы:

Похожие инструкции для KINNEY KT150

Бренды по названию

Популярные бренды