Tuthill KINNEY KT150 Скачать руководство пользователя страница 7

Страница: 7 / 50

Manual 1843 Rev B p/n 001843 0000

CONGRATULATIONS

on the purchase of a new

KINNEY

KT™

Single-Stage, Triplex Rotary Piston

Vacuum Pump from Tuthill Vacuum & Blower

Systems. Please examine the pump for shipping

damage, and if any damage is found, report it

immediately to the carrier. If the pump is to be

installed at a later date, make sure it is stored in a

clean, dry location and rotated regularly. Make sure

covers are kept on all openings. If pump is stored

outdoors, be sure to protect it from weather and

corrosion.

This manual applies to Kinney Vacuum models

KT-150, KT-300, KT-500 and KT-850. Become

thoroughly familiar with these instructions before

attempting to install, operate or repair this unit.

Consult Tuthill Vacuum & Blower Systems

when problems arise that cannot be resolved

after reading this manual. Always include pump

nameplate information when ordering parts or

components.

KINNEY KT

vacuum pumps are built to exacting

standards and, if properly installed and maintained,

will provide many years of reliable service. Read

and follow every step of these instructions when

installing and maintaining the pump.

WARNING

Serious injury can result from operating or
repairing this machine without first reading the
service manual and taking adequate safety
precautions.

OTE:

Record the pump model and serial

numbers in the OPERATING DATA form

on the inside back cover of this manual.

Use this identification on any replacement

part orders, or if service or application

assistance is required.

APPLICABLE DOCUMENTATION

The applicable documents associated with this

manual are:

• EN 1012-1:1996 - Compressors and vacuum

pumps - Safety Requirements - Part 2: Vacuum

Pumps

SCOPE OF MANUAL

The scope of this manual includes the KT Series

rotary piston pumps.

INTRODUCTION

Содержание KINNEY KT150



















































Результаты поиска

Содержание KINNEY KT150

Отзывы:

Похожие инструкции для KINNEY KT150

Бренды по названию

Популярные бренды

Tuthill KINNEY KT150, Руководство оператора

Результаты поиска

Содержание KINNEY KT150

Отзывы:

Похожие инструкции для KINNEY KT150

Бренды по названию

Популярные бренды