Tuthill KINNEY KT150 Скачать руководство пользователя страница 35

Страница: 35 / 50

Repair Instructions

Manual 1843 Rev B p/n 001843 0000

4. The belts should not slip if they are correctly

adjusted and the correct starting procedure

is used. A screeching noise at start-up may

indicate the belts are too loose. Belt dressing

should not be used on V-belts. Sheaves and

V-belts should remain free of oil and grease.

Tension should be removed from belts if the

drive is to be inactive for an extended period of

time.

DISASSEMBLY

The following steps are for complete disassembly

of the pump; however, the pump should be

disassembled only to the extent necessary for

servicing. Refer to assembly drawings and parts

lists as needed. Note that the open head is

the head through which the shaft extends, and

closed head is the head on which the oil pump is

mounted.

1. Disconnect all manifolding, water lines, and

electrical connections, and drain the oil.

2. Remove the belt guard and belts.

3. Remove the oil lines from both ends.

4. Remove the motor from the top of the pump.

5. Remove the pump sheave and drive key.

6. Remove the oil sight gauge from the separator

cover. Remove the inspection cover from the

separator.

7. Remove the separator housing and gasket

from the cylinder.

The separator housing has threaded holes to

receive eye bolts for lifting the pump. When the

separator housing is removed, do not attempt

to lift the pump cylinder by using the gas

ballast or oil drain piping to attach or support

rigging for hoisting the cylinder.

8. Unscrew the air/oil separator assembly.

Remove the valve cover from the cylinder.

9. Remove the discharge valves. If valves are

disassembled, be sure to understand the

procedure for proper reassembly.

10. Remove bearing retaining plate.

11. Unscrew the retainer nut from the shaft.

12. Remove the cap screws from the housing.

13. Remove the bearing, housing and stationary

parts of the shaft seal.

14. Remove the rotating part of the shaft seal.

15. Remove the oil pump and housing from the

closed head. Remove the closed head using

two securing bolts as jackscrews to break

the seal between head and cylinder after

all securing screws are removed. Press the

sleeve bearing from the head.

16. Withdraw the slide pin, piston, cam and slide-

pin spacer.

17. Remove the retaining ring from the shaft.

Loosen the socket head self-locking screws in

the removable wall to release the pins securing

the wall to the cylinder. Remove the wall, being

careful not to cock it as it is removed.

18. Withdraw the slide pin, piston and slide-pin

spacer.

19. Remove the open head following the same

procedure as removing the closed head and

press the bearing from the head.

20. Withdraw the piston, slide pin and cam.

21. The shaft and center cam can be taken out of

the closed head end of the pump. Press the

center cam from the shaft.

Содержание KINNEY KT150



















































Результаты поиска

Содержание KINNEY KT150

Отзывы:

Похожие инструкции для KINNEY KT150

Бренды по названию

Популярные бренды

Tuthill KINNEY KT150, Руководство оператора

Результаты поиска

Содержание KINNEY KT150

Отзывы:

Похожие инструкции для KINNEY KT150

Бренды по названию

Популярные бренды