TurfEx TS-50 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 16

TurfEx TS-50 Скачать руководство пользователя страница 16

TrynEx International
531 Ajax Drive
Madison Heights, MI 48071-2429

www.turfexproducts.com

Lit. No. 76736, Rev. 00

July 1, 2020

Copyright © 2020 Douglas Dynamics, LLC. All rights reserved. This material may not be reproduced or copied, in whole or in part, in
any printed, mechanical, electronic,

fi

lm, or other distribution and storage media, without the written consent of TrynEx International, LLC.

Authorization to photocopy items for internal or personal use by TrynEx International outlets or spreader owner is granted.

TrynEx International reserves the right under its product improvement policy to change construction or design details and furnish equipment
when so altered without reference to illustrations or speci

fi

cations used. TrynEx International may require or recommend optional equipment

for spreaders. TrynEx International o

ﬀ

ers a limited warranty for all spreaders and accessories. See separately printed page for this important

information. The following are registered (

®

) trademarks of Douglas Dynamics, LLC: TurfEx

®

.

Printed in U.S.A.

«
...
14
15
16

Содержание TS-50

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды