TURFCO T3000 85872 Скачать руководство пользователя страница 15

Страница: 15 / 20

85872 RevA

TURFCO T3000 APPLICATOR

LOCKING KNOB

SPREADER GATE

OPEN/CLOSE CONTROL HANDLE

VARI-RATE

ADJUSTABLE

GATE STOP

FIGURE 10

SPREAD TRIM BORDER PATROL

SPREADER SPINNER

WHEEL SPEED

CONTROL

OP85872-14

OFF

NARROW

WIDE

OPEN

CLOSE

60%

FULL

OPERATION

5. SPINNER WHEEL

(See Figure 8 and 9) -

The

Spinner Wheel broadcasts the material from

the hopper. The speed of the spinner wheel is

controlled by the Spinner Speed Control.

6. SPINNER SPEED CONTROL

(See Figure 8 and

10) -

The Spinner Speed Control lever allows the

operator to speed up or slow down the spinner

wheel to vary the spread pattern width. Push the

Spinner Speed Control lever full ahead for full

application width and pull back for the narrow or

trim width. A slower spinner wheel speed results

in a narrower spread width (about 7 foot wide)

for use in narrow spots, trimming, and to avoid

putting product where it is not wanted.
Note: The Spinner Speed Control lever should

only be moved when the engine is running. No

damage will occur if the lever is moved while the

engine is not running, it is just better for the belts

and pulley to be moving when activated.

7. SPREADER GATE OPEN/CLOSE CONTROL

(See Figure 10) -

The Spreader Gate Open/

Close Control handle controls the opening of

the spreader gate. Push forward to the open the

gate or pull back to close.

8. VARI-RATE ADJUSTABLE GATE STOP

(

See

Figure 10) -

Vari-Rate Adjustable Gate Stop is

located next to the spreader gate handle. The

stop will limit the movement of the spreader

gate control handle. This causes the spreader

gate to stop at a preset opening size that is less

than 100% open (opening must be preset during

calibration). To use the Vari-Rate stop, simply

push the lever in as you open the gate. The lever

will snap in to a more vertical position and stop at

the gate stop. To bypass the stop, tip the control

out as you move it forward to open the gate and

the handle will miss the stop allowing the gate to

fully open.
The Vari-Rate Adjustment Gate Stop should only

be set by the person calibrating the spreader.

This should never be done in the ﬁeld and

should be changed whenever the calibrated

rate is changed.

The exact setting for the Vari-

Rate should only be set by licensed persons.

Refer to the spreader calibration section in this

manual.

9. SPREAD TRIM BORDER PATROL

(See Figure

8 and 10) -

The Spread Trim Border Patrol

deﬂector is on the left side of the hopper and

is operated by a lever on the left side of the

operators panel. The Border Patrol deﬂector is

operated by pushing the lever down for trim and

up for full width application.

Содержание T3000 85872





















Результаты поиска

Содержание T3000 85872

Отзывы:

Похожие инструкции для T3000 85872

Бренды по названию

Популярные бренды

TURFCO T3000 85872, Руководство оператора

Результаты поиска

Содержание T3000 85872

Отзывы:

Похожие инструкции для T3000 85872

Бренды по названию

Популярные бренды