TURFCO 85874 Скачать руководство пользователя

Страница: 38 / 41

85874 & 85875 Rev C

TURFCO T3000i SERIES APPLICATOR

SERVICE AND MAINTENANCE

ENGINE

OIL DIPSTICK

AND FILLER

ENGINE

AIR CLEANER

TRANSAXLE

RESERVOIR

TANK

REMOVE STORAGE TRAY

TO CHECK ENGINE

FIGURE 26

SV85874-02

GREASE FITTING LOCATIONS

(TOTAL OF 4)

AS VIEWED FROM BOTTOM

REAR OF MACHINE

FRONT AXLE

CENTER SWIVEL (QTY 1)

FRONT

STEERING

ARMS

(QTY 2)

IDLER ARM

SUPPORT (QTY 1)

FIGURE 27

SV85874-03

ENGINE AND TRANSAXLE

(See Figure 26)

Engine:

CHECK OIL LEVELS DAILY.

Follow the

engine manufacturer’s manual for intervals of oil

change, oil filter replacement, proper oil types, and

fill levels for the engine. Inspect and clean/replace

the engine air filter as needed.

Engine Carburetor Linkages and Springs:

CLEAN AND LUBRICATE WEEKLY.

Clean and

remove fertilizer dust from the linkages, governor

springs, choke linkage on the carburetor with carb

cleaner. Lightly lubricate to protect from rust.

Wipe

away excess lubrication that will attract and collect

dust, dirt and debris.

Transaxle:

Check the level of fluid in the transaxle

reservoir. Fill only to the “Full Cold” level mark on

the reservoir (located very low on reservoir). Use

20W/50 engine oil for the transaxle. Do not overfill.
Transaxle capacity is 95.5 fluid ounces (2.8 Liter/3

quarts). Add extra to allow for filter, the reservoir

and the reservoir hose (approximately one quart).

GREASE FITTINGS

(See Figure 27)

Grease Fittings:

(qty 4) Grease after every 8 hours

of operation.

Wipe away excess lubrication that will

attract and collect dust, dirt and debris.

Lubrication

Содержание 85874










































Результаты поиска

Содержание 85874

Отзывы:

Похожие инструкции для 85874

Бренды по названию

Популярные бренды

TURFCO 85874, Руководство оператора

Результаты поиска

Содержание 85874

Отзывы:

Похожие инструкции для 85874

Бренды по названию

Популярные бренды